Yamaha RX-V2065 - Инструкция (Страница 64)

62
En
Controlling other components with the remote control
You can program remote control codes from other remote
controls. Use this feature if you want to program functions
not included in the basic operations covered by the remote
control codes, or an appropriate remote control code is not
available.
Note
<Note> • Each of the steps described in this section should be performed within
one minute after the last step. If the next operation is not performed
within one minute, the programming operation is canceled. In this case,
start again from the beginning.
You can program the remote control to make functions of
an external component operable with the following keys.
You can assign functions to these keys for each input
source as with remote control codes.
cSOURCE POWER
kExternal component operation keys
lNumeric keys
y
• The remote control transmits infrared rays. If the remote control of the
external component also uses infrared rays, this remote control can learn
most of its functions. The remote control may not recognize special or
consecutive signals.
• The keys may not operate the assigned functions depending on operating
conditions of this unit.
1
Press oCODE SET on the remote control
using a pointed object such as the tip of a
ballpoint pen.
nTRANSMIT blinks twice.
2
Press the desired dInput selection key.
3
Press lNumeric keys to enter “9990”.
4
Press a key to which you want to assign the
function.
nTRANSMIT lights up and this unit enters a wait
state to receive remote control signals. Perform steps
5 and 6 within 10 seconds.
Note
<Note> • If 10 seconds pass after this unit enters the wait state, a timeout
error occurs and nTRANSMIT turns off. In this case, repeat
from step 4.
5
Place the remote control about 5 to 10 cm
apart from the remote control of the external
component on a flat surface so that their
infrared transmitters are aimed at each other.
6
Press the key on the remote control of the
external component.
If the learning process is complete, nTRANSMIT
blinks twice. If it fails, nTRANSMIT blinks six
times. Repeat from step 4.
y
• Repeat steps 4 thorough 6 to assign a function to another key.
7
To end the operation, press oCODE SET
again.
nTRANSMIT blinks once.
1
Press oCODE SET on the remote control
using a pointed object such as the tip of a
ballpoint pen.
nTRANSMIT blinks twice.
2
Press the desired dInput selection key.
3
Press lNumeric keys to enter “9991”.
4
Press a key you want to reset.
If the key assignment is cleared, nTRANSMIT
blinks twice. If it fails, nTRANSMIT blinks six
times. Repeat from step 1.
y
• Repeat step 4 to clear another key assignment.
5
To end the operation, press oCODE SET
again.
nTRANSMIT blinks once.
1
Press oCODE SET on the remote control
using a pointed object such as the tip of a
ballpoint pen.
nTRANSMIT blinks twice.
2
Press the desired dInput selection key.
3
Press lNumeric keys to enter “9992”.
If the key assignments are cleared, nTRANSMIT
blinks twice. If it fails, nTRANSMIT blinks six
times. Repeat from step 1.
Programming from other remote
controls
Programming the remote control of this unit
BD DV
D
TV
CD
RADIO
SLEEP
FM
AM
INFO
MEMOR
Y
1
2
3
4
1
2
3
4
5
6
1
2
PHONO
MUL
TI
DOCK
TUNER V- A U X
HDMI
MUSIC
STEREO ENHANCER
SUR.
DECODE
MO
VIE
STRAIGHT
HDMI OUT
PURE DIRECT USB/NET
PRESET
TUNING
ON SCREEN
OPTION
SOURCE PO
WER
SCENE
RETURN
ENTER
V O LUME
DISPLA
Y
HDMI
AU
D
IO
TRANSMIT
CODE SET
MAIN
ZONE 2
ZONE 3
AV
PO
WER
5 to 10 cm
Remote control of external component
Clearing the assignment of each key
Clearing the assignments of all keys