Yamaha RX-V765 - Инструкция (Страница 33)

31
En
English
INTR
ODUCTION
AD
DITIONAL
INFORMA
T
ION
APPENDIX
PRE
P
ARA
T
ION
BA
S
IC
OPERA
T
ION
AD
V
ANCED
OPERA
T
ION
The FM/AM tuner of this unit provides the following two
modes for tuning.
■ Frequency tuning mode
You can tune into a desired FM/AM station by searching
or specifying its frequency.
■ Preset tuning mode
You can preset the frequencies of FM/AM stations by
registering them to specific numbers, and later just select
those numbers to tune in.
Note
• Adjust the FM/AM antennas connected to this unit for the best reception.
1
Rotate the RINPUT selector (or press
eTUNER) to switch the input source to
“TUNER.”
2
Press IFM (fFM) or IAM (fAM) to select
a band.
“FM” or “AM” appears on the front panel display
according to the band that you have selected.
3
Press JTUNING l / h (or fTUNING k / n)
to specify the frequency.
To adjust the frequency to a higher range, press h (or
k). To adjust it to the lower range, press l (or n).
The TUNED indicator on the front panel display
lights up when the tuner is tuned into a station. The
STEREO indicator also lights up if the program being
broadcasted is in stereo.
The frequency changes in the following manner according
to how you press JTUNING l / h (or fTUNING
k / n).
When you press the key more than 1 second
The tuner searches the frequency of a station that is
detectable around the current frequency. This is effective
when the tuner can receive strong signals without any
interference. Once the search starts, release the key.
When you press and release the key
The tuner increases or decreases the frequency in steps.
Use this method when the tuner cannot receive strong
signals and stations are skipped during the search.
y
• You can switch between stereo and monaural for FM broadcast in the
OPTION menu (see page 41).
4
To tune in by direct frequency tuning, enter
the frequency of the desired station using
mNumeric keys on the remote control.
Enter only integers. For example, if you want to set
the frequency to 88.90 MHz, enter “8890” using
mNumeric keys.
Notes
• When you press mNumeric keys during preset tuning, a
preset number is selected. Set tuning mode to frequency tuning
mode using JTUNING l / h (or fTUNING k / n) prior to
the operation.
• “Wrong Station!” appears on the front panel display when you
enter a frequency that is out of receivable range. Make sure that the
entered frequency is correct.
• You do not need enter zero if it comes at the end of a decimal
number. For example, enter “925” for “92.50 MHz” or “940” for
“94.00 MHz.”
You can register up to 40 FM/AM stations (Preset) using
the automatic station preset feature or manual station
preset feature.
The tuner automatically detects FM stations with strong
signals and registers up to 40 stations. AM stations cannot
be automatically registered. Use manual station preset.
1
Rotate the RINPUT selector (or press
eTUNER) to switch the input source to
“TUNER.”
2
Press rOPTION on the remote control.
The OPTION menu screen for setting options of
tuner input appears on the front panel display.
y
• For details on the OPTION menu, see page 39.
• The OPTION menu is displayed on the video monitor.
3
Select “Auto Preset,” using kCursor k / n
and press kENTER.
Automatic station preset starts about 5 seconds later
from the lowest frequency upwards.
FM/AM tuning
Tuning into the desired FM/AM station
(Frequency tuning mode)
STEREO
TUNED
FM 92.50MHz
Registering FM/AM stations and
tuning in (Preset tuning mode)
Registering stations by automatic station
preset
Auto Preset