Перезапись части песни, Re-recording parts of a song, Recmode extratrackch=3 start:norm end:replace – Инструкция по эксплуатации Yamaha CP300
Страница 44
Руководство пользователя CP300
Перезапись части песни
В этой главе объясняется, как записать отдельную часть песни снова.
1
Нажмите кнопки
B [– (NO)][+ (YES)], когда на дисплее отображается переход вос-
произведения через такты, или воспроизведите запись заново и нажмите кнопку
[PLAY/PAUSE], отметив тем самым точку, находящуюся чуть ранее начала части
записи, которую вы хотите переписать.
если значок воспроизведения не отображается на дисплее, снова нажмите одну из кнопок SO���
SE�E�T [
[
] [
]
] ещё раз.
отображает текущий такт
текущий такт
текущий такт
такт
такт
слова “�ar” и “measure” взаимозаменяемы
“�ar” и “measure” взаимозаменяемы
и “measure” взаимозаменяемы
“measure” взаимозаменяемы
взаимозаменяемы
Recording Your Performance
CP300 Owner’s Manual
44
Basic Oper
ation
This section explains how to record a specific section or part of a Song again.
1
Use the B [– (NO)][+ (YES)] buttons while the playback display is displayed to move
through the measures, or play back the recording and press the [PLAY/PAUSE]
button to locate a point slightly prior to the beginning of the part you wish to re-
record.
If the playback display does not appear, press one of the SONG SELECT [N][O] buttons once.
2
Select a Voice or Voices for recording, if necessary.
Repeat Step 2 on page 42 if you wish to change the previous settings.
3
Press and hold down the [REC] button, and press one of the C [–][+] buttons
repeatedly to specify how the recording should start. Similarly, use the D [–][+]
buttons to specify how the recording should end.
While you are holding down the [REC] button, the following recording method select display appears.
Starting methods:
Norm: All existing data in the Song will be erased after re-recording starts.
Key On: Data that exists prior to the point where you start playing a note will not be erased (when re-
recording part of the Song).
Ending methods:
Replace: Existing data following the point at which you stopped recording will be erased.
Punch Out: Existing data following the point at which you stopped recording will remain.
4
Select a recording track, then start recording.
After this, follow the procedure beginning with Step 3 on page 42.
Re-recording Parts of a Song
PresetSong Bar 012
P-000:NewSong
NO
YES
A
B
D
C
Indicates the current measure.
(The words “bar” and “measure” are used interchangeably.)
RecMode ExtraTrackCh=3
Start:Norm End:Replace
NO
YES
A
B
D
C
2
В случае необходимости выберите тембр или тембры для записи
Повторите шаг 2 на странице 42, если хотите изменить предыдущие настройки
3
Нажмите и удерживайте кнопку
[REC], затем нажмите несколько раз одну из
кнопок
C [–][+], чтобы определить, как должна начинаться запись. Точно так же
нажимайте одну из кнопок
� [–][+], чтобы определить, как должна закончиться
запись.
Во время удерживания кнопки
[REC], на дисплее появится следующее сообщение
Recording Your Performance
CP300 Owner’s Manual
44
Basic Oper
ation
This section explains how to record a specific section or part of a Song again.
1
Use the B [– (NO)][+ (YES)] buttons while the playback display is displayed to move
through the measures, or play back the recording and press the [PLAY/PAUSE]
button to locate a point slightly prior to the beginning of the part you wish to re-
record.
If the playback display does not appear, press one of the SONG SELECT [N][O] buttons once.
2
Select a Voice or Voices for recording, if necessary.
Repeat Step 2 on page 42 if you wish to change the previous settings.
3
Press and hold down the [REC] button, and press one of the C [–][+] buttons
repeatedly to specify how the recording should start. Similarly, use the D [–][+]
buttons to specify how the recording should end.
While you are holding down the [REC] button, the following recording method select display appears.
Starting methods:
Norm: All existing data in the Song will be erased after re-recording starts.
Key On: Data that exists prior to the point where you start playing a note will not be erased (when re-
recording part of the Song).
Ending methods:
Replace: Existing data following the point at which you stopped recording will be erased.
Punch Out: Existing data following the point at which you stopped recording will remain.
4
Select a recording track, then start recording.
After this, follow the procedure beginning with Step 3 on page 42.
Re-recording Parts of a Song
PresetSong Bar 012
P-000:NewSong
NO
YES
A
B
D
C
Indicates the current measure.
(The words “bar” and “measure” are used interchangeably.)
RecMode ExtraTrackCh=3
Start:Norm End:Replace
NO
YES
A
B
D
C
методы начала записи:
Norm: все существующие данные в песне будут стёрты после начала перезаписи
�e�� �n: данные, находящиеся перед отмеченной точкой начала перезаписываемой части, сохранят-
ся (во время перезаписи части песни)
методы окончания записи:
�eplace: все данные, находящиеся после окончания записи, будут стёрты
Punch �ut: все данные, находящиеся после окончания записи, будут сохранены
4
Выберите звуковую дорожку для записи, затем начните запись
После этого, следуйте инструкциям, начиная с шага � на странице 42.
Выбор параметров исполнения