Инструкция по эксплуатации ZELMER 478
Страница 79
83
Construction of the appliance
(Fig. A)
1
Motor
a
power on/off button
b
gear 1 – gear 2 / turbo button
c
indicator light
d
pulse button (does not apply in case of juice extractor)
e
skimmer
f
sucker
g
power supplying cord
JUICE EXTRACTOR SET
2
Juice container
h
spout
i
cover
3
Body of the juice collector
4
Strainer
5
Lid
6
Clamps
7
Pusher
8
Pulp container
MIXING CUP SET
9
Mixing cup
10
Lid
11
Feeder
COFFEE GRINDER SET
12
Coffee grinder
13
Container
14
Lid
Characteristics of the juice extractor
The juice extractor is an electrical appliance for fast fruit and
vegetable juice centrifuging with automatic separation of
pulp. The raw material is first pulped and next the juice is
centrifuged from the pulp. A simple and easy operation of the
appliance enhance its utility advantages. An electronic speed
stabilizer ensures a constant rotation speed irrespectively of
loading, which guarantees obtaining of juice even consistency.
The juice extractor is equipped with 2 centrifuging speeds
(for hard and soft fruit) which were chosen to obtain the
optimal quality parameters for squeezed juices. Keeping the
maximal content of fruit pulp and fibre containing vitamins,
pectin, enzymes and minerals in the juice results in its lower
clarity. This is an intended effect since the Producer of the
juice extractor decided that it is more important to keep the
highest possible nutritious, health and dietetic values of the
obtained fruit than its clarity. The juice extractor is additionally
equipped with filter self-cleaning function. After pressing the
turbo button, the engine works for about 3 seconds with high
rotation. High rotation helps to clean the filter in the event of
vibrations resulting from excessive pulp accumulation. The
turbo function may be used in 10-second intervals only. The
juice extractor may work for 15 minutes without any break.
The quantity of juice obtained, e.g. from 1 kg of a raw material
depends on its freshness as well as on filter cleanliness and
the state of the pulping blade. The parts in contact with the
processed raw materials are made of materials permitted for
contact with food.
Juice extractor safety operation instructions
Do not use the juice extractor if the spinning strainer is
●
damaged.
Make sure that the lid is clamped securely in place before
●
motor is turned on.
Do not unfasten clamps when the juice extractor is in
●
operation and the strainer is spinning because the safety
system will cause the appliance to stop.
Use the pusher only to push food into the feeder
●
opening.
Do not overload the appliance with excessive amounts of
●
food or too intense pushing (with the pusher).
Immediately turn off the juice extractor if you notice
●
strong vibrations or the rotation speed is reduced. Clear
the strainer and its cover.
Turn the motor off and unplug the appliance if food is
●
blocked in the feeder opening or on the grinding blades.
Remove the cause of blocking.
Use hard bristle brush for cleaning the strainer with sharp
●
grinding blade.
Do not use the juice extractor without pulp collector.
●
Do not overload the appliance with extensive amount
●
of product or do not push it to strong (with a pusher),
because a sudden increase of juice amount in the bowl
spout can cause the juice overflow out of the lid or into
pulp collector.
Preparation of the juice extractor for
operation (disassembling)
(Fig. C)
Before using the juice extractor for the first time, disassemble
it and wash parts in contact with the processed product.
Place the juice extractor near the socket on the firm,
●
clean and dry surface.
1
Pull down the clamps (6) so that the tracks moved out of
grooves of the lid (5).
2
Take the pusher (7) and the lid (5) out.
3
Then remove the juice collector (2) including the body
(3) and the filter (4). To this end, turn the body (3) right
(clockwise) to the limit and raise the body with the juice
collector and the filter.
4
Finally, disassemble the juice collector (2) from the
body (3).
Wash the disassembled parts (except the motor unit)
●
carefully in hot water and wash-up liquid. You can also
clean them in a dishwasher in max temp. 60°C (except
for the strainer and the motor unit). After drying them
carefully, start assembling the clean parts.