Инструкция по эксплуатации ZELMER 481
Страница 110
114
The level of products inside the bowl should not
exceed the hight of mixers or whisks working part (L).
Operation with liquidising disc (Fig. E)
Liquidizing disc is used for liquidizing boiled fruit and
●
vegetables such as: carrots, potatoes, tomatoes, apples
through the sieve. It partly replaces the function of the
mixing adapter.
1
Insert the liquidizing disc on the whisk with toothed bar
from the bottom side.
2
Insert the whisk into the socket marked with a star.
Cup (12)
Made of transparent material is used as a container when
mixing adapter is used.
Operation with mixing adapter (Fig. F)
You can use the mixing adapter for:
mixing liquids,
●
crumbling boiled vegetables and raw, soft fruit,
●
preparing different mayonnaise and pastes,
●
preparing soups for infants.
●
You can assemble the adapter after moving the cover.
1
Gently press the bolt and slide towards the direction
shown in the figure.
2
Insert the threaded part into the motor casing hole and
screw it turning right until you feel the refusal.
Inadequate screwing of the mixing adapter can result
in clutch damage or the adapter damage.
3
Put the adapter into the processed product and switch
the mixer on.
Operation with mixing cup (Fig. G)
CAUTION! Hold the mixer in your hand all the time
during operation.
Mixing cup is intended for infant soups preparation, milk
shakes or pancake dough.
1
It has the label „500 ml max” on both sides, which
indicates the maximum level of product to fill the cup and
graphic scale to determine the volume 200 ml to 500 ml
(according to the symbols in the drawing beside).
2
After moving the cover (like during assembling the
adapter) assemble the cup the following way: Insert the
mixing cup on the motor part so that the 3 buckles visible at
the bottom of the cup got into the nuts of the motor casing.
3
Holding the motor casing handle turn the cup clockwise
direction until you feel the refusal.
You shall obtain the proper connection, when the 3 buckles get
under the motor casing, and the fastener on the cup rib move
on the other side of the spherical buckle on the motor casing.
4
Fill the cup with products and put the cover with the doser
on – you can add next products to the cup during operation.
Operation with stand including turnable bowl (Fig. H)
The stand with assembled motor part makes the operation
with whisks or mixers easy, as the user does not have to hold
the device.
The housing with the bowl is equipped with a self
gathering spatula, which is an innovative solution. It
helps to effectively blend the products, prevents the dough
from gathering on the edges of the bowl and shortens the
preparation time.
The stand head driver automatically makes the head move
pendulum-like and simultaneously turns the bowl with the
mixed product.
You can use the stand with specially prepared whisks and
mixers only. The device equipped with stand includes also
one mixer and one whisk with toothed bar.
1
Insert the mixers or whisks into the motor casing (as
described above).
2
Assemble the drive in the stand head after moving the
cover (like during assembling the adapter) the following way:
Insert the drive fasteners (which are located near the holes
for whisks assembling) under the stand head fastener.
3
Turn the control clamp to the limit in such a way that the
hand is positioned vertically.
4
Press the fastener button and simultaneously deflect the
stand head with the motor part back.
5
If the bowl with products a bit up and then insert it on the
three insertions and place it at the stand base.
6
If necessary, install the self-gathering spatula.
7
Place the stand head with the motor part in horizontal
position (you will hear the clicking sound of fastener blocking
clamps).
8
Start-up the mixer with the switch lever and it will make
the bowl turn and the head with drive move pendulum-like.
Never block or stop the oscillatory movement during
operation. It may cause damage to the housing.
Working with a stand with scales
Food mixer type 481.67 has the base, which is equipped with
rotating bowl and inbuilt electronic scales, which is an
innovative solution. The base with installed motor makes
the work with whiskers or stirrers easier, so that the user
has „free” hands, whereas the assembled scales enable for
weighting of processed products directly in the base bowl.
The base with the scales is equipped with the scraper blade
and the blade.
ATTENTION! Equipment of the blender type 481.67 is
identical to type 481.7 – see table (B); the additional
equipment is a stand with scales, which should be
operated according to this instruction manual.
The base with scales is equipped with safety blocking,
which prevents the damages of the scales sensor, it is
started by blocking knob.
1 cm
L
1 cm
L