Maintenance / уход и обслуживание – Инструкция по эксплуатации Sulky Maxidrill TRW 4/6 m central metering unit
Страница 95
H
Settings
a) Skim coulter settings
In order to ensure that the drilling discs rotate
continuously, it is particularly important to correctly
adjust the skim coulter
pressure on the discs.
Too much pressure might block the discs when
drilling at shallow depths, not enough might lead to
packing of debris between the skim coulters and
the discs, quickly leading to blockages.
The skim coulter is held on the disc support via
elastomer washers
, which allow a certain
flexibility in the contact pressure of the skim coulter
on the disc.
The skim coulter
pressure is adjusted using the 2
nuts
that hold it in place on the disc arm.
The correct setting is achieved when the skim
coulter is touching the disc but it is still possible to
pull it away from it by hand (by compressing the
elastomer washers
). In this case, the skim
coulter only touches the disc at point
A
. Check that
points
B
and
C
are not touching the disc. All of the
inside surfaces of the skim coulter which face the
disc should be “open” so as not to trap debris whilst
working.
If one of points
B
or
C
touches the disc at the same
time as point
A
, modify the tightness of one of the
holding nuts so as to angle the skim coulter and
move these points away from the disc.
b) Adjusting the wheel scrapers
The scraper position can be adjusted in relation to
the wheel. Adjust the position to maintain a
minimum space of 3 mm between the scraper and
the tyre.
If the gap is set at less than 3 mm, the tyre is at risk
of being damaged by the scraper or by stones that
might become trapped.
2
2
3
3
1
1
2
2
1
1
93
GB
RU
Maintenance / Уход и обслуживание
H
Регулировка дерноснимов
a) Регулировка дерноснимов
С целью обеспечения постоянного вращения
посевных дисков особенно важно регулировать
давление дерноснимов
на дисках. Слишком
большое давление может привести к блокировке
дисков в случае поверхностного посева,
недостаточное давление вызывает извлечение
остатков между дерноснимом и дисками, быстро
вызывая блокировку последних.
Дерносним установлен на опоре диска с
использованием шайб из эластомера
, которые
несколько снижают давление дерноснима на диск.
Давление дерноснима
регулируется с помощью 2-
х гаек
, которые поддерживают ее на кронштейне
диска.
Правильная регулировка достигается, когда
дерносним касается диска, но его еще можно
отвести вручную (т.е. он прижат эластичными
шайбами
). В этом случае дерносним касается
диска только на уровне точки
A
. Убедиться, что
точки
B
и
C
не касаются диска. Все внутренние
поверхности дерноснима, обращенные к диску,
должны быть «открыты» во избежание попадания
отходов во время работы.
Если одна из точек
B
или
C
касается диска
одновременно с точкой
A
, изменить степень
затяжки одной из удерживающих гаек, так, чтобы
наклонить дерносним и удалить эти точки от
диска.
b) Регулировка очистителей колеса
Положение очистителя регулируется
относительно колеса. Необходимо
отрегулировать положение для сохранения
пространства между очистителем и покрышкой
не менее 3 мм. В случае если расстояние менее 3
мм, существует риск повреждения шины
скребком или забившимся галечником.
2
2
3
3
1
1
2
2
1
1
1
4