ZELMER 13Z015 - Инструкция (Страница 97)

14.
Always ke to provide high quality of brewed coffee and extend the life-span of the
mac
and unplug it from the power supply.
4. Do not wash any part of the espresso machine in a dishwasher.
6. R
an
7. D
) sso machine and pour water out of them. Then
15.
IS
Cleaning and care
ep the espresso machine clean in order
hine.
1. Before you start cleaning, turn the espresso machine off
2. Make sure that the espresso machine has cooled off.
3. Do not immerse the espresso machine in water or any other liquids.
5. Wipe the casing of the machine with a wet cloth or sponge.
emove the filter handle (6) from the coffee machine and then remove coffee grounds. Clean the filter handle (6)
d the filter with a wet cloth or sponge.
ry the cleaned part on air or with the use of a cloth – do not dry them in an oven or a microwave.
8. Remove the drip tray grid (7 and the drip tray (8) from the espre
clean them with a wet cloth or sponge.
9. Remove the cappuccino attachment by unscrewing it and pulling it downwards.
Troubleshooting
SUE POSSIBLE CAUSE POSSIBLE SOLUTION
Co
the
handle
he filter handle (6) is not attached properly or not
placed in the brew head (4) and is maximally
T
Make sure that the filter handle (6) is properly
ffee flows out from
back of the filter
tightened.
tightened enough.
There are coffee grains on the edge of the filter
handle (6). Clean the upper edge of the filter handle (6) from
coffee and wipe the brew head (4) clean.
The brew head (4) is dirty. Wipe the brew head (4) with a wet cloth.
The brew head (4) is damaged. Contact an authorized service center.
No water in the water tank (1). Fill the tank (1) with water.
Co
out ffee does not flow
The water tank(1) is not properly installed.
correctly.
Push the water tank (1) in making sure it is placed
The control (12) is set to some oth Make sure that the control (12) is set to the er position, e.g.
.
position.
The filter on the brew head (4) may be blocked. See paragraph 13 – Descaling.
The sieve in the filter (6) is blocked. Coffee is too
runnin
Empty the sieve in the filter (6) and rinse it in
g water. Wipe the brew head (4) with
a cloth.
finely ground or too compressed.
Co
dro
do not
ffee is poured in
ps
Coffee is too finely ground or too compressed.
compress it too much.
If you use extremely fine ground coffee
The machine is blocked by calcareous residues . See paragraph 13 – Desc g. alin
Coffee is stale or dry.
Use fresh coffee. After opening a package of
it is stored coffee be sure in an airtight container.
Espresso is without the
characteristic foam Coffee is not compressed enough. Compress the coffee harder.
Coffee is too coarsely ground.
Use properly ground coffee or change your coffee
brand.
Not enough coffee in the sieve of the filter (6). See paragraph 8 – Preparing espresso.
The handle is loose
during the brewing
process
The coffee is compressed too much. Compress the coffee more gently.
Coffee is too finely ground. Change your coffee to a more coarsely ground.
The filter handle (6) does not fit tightly, as it was
not screwed hard enough.
Make sure that the filter handle (6) is properly
placed in the brew head (4) and is maximally
tightened.
There are coffee grains on the edge of the filter
handle (6). Clean the upper edge of the filter handle (6) from
coffee and wipe the brew head (4) clean.
The brew head (4) is dirty. Wipe the brew head (4) with a wet cloth.
The brew head (4) is damaged. Contact an authorized service center.
No steam doming out
of the nozzle The steam nozzle (10) is blocked. Clean and rinse the steam nozzle (10).
Not enough foamed
milk
milk is not fresh. Make sure ilk is fresh. The that the m
The temperature of milk is too high.
Make sure that the milk is properly cooled off
before being used.
The pot.
To achieve the best results in foaming use the
stainless steel pot delivered with the machine and
as far as possible try to cool it off and rinse it with
cold water before use.
The steam nozzle (10) is blocked. Clean and rinse the steam nozzle (10).
The milk is boiled. Try to use some fresh, cool milk.
The machine is not
working The filter on the brew head (4) may be blocked. See paragraph 13 – Descaling.
The machine is blocked with limescale. See paragraph 13 – Descaling.
97