Инструкция по эксплуатации Yamaha CLP-230 RU
Страница 82
Внимание! Текст в этом документе был распознан автоматически. Для просмотра оригинальной страницы Вы можете воспользоваться режимом "Оригинал".
CLP240E.book Page 82 Wednesday, April 6, 2005 4:02 PM
(2) Universal Non-Realtime Message (GM On)
General MIDI Mode On
Data format: [F0H] -> [7EH] -> [XnH] -> [09H] -> [01H] ->
[F7H]
Exclusive status
Universal Non-Realtime
ID of target device
Sub-ID #1=General MIDI Message
Sub-ID #2=General MIDI On
End of Exclusive
F0H =
7EH =
7FH =
09H =
01H =
F7H =
or
F0H =
7EH =
XnH =
Exclusive status
Universal Non-Realtime
When received, n=0~F
X = don't care
09H = Sub-ID #1=General MIDI Message
01H = Sub-ID #2=General MIDI On
F7H = End of Exclusive
When the General MIDI mode ON message is received, the
MIDI system will be reset to its default settings.
This message requires approximately 50ms to execute, so
sufficient time should be allowed before the next message is
sent.
8. SYSTEM EXCLUSIVE MESSAGES (XG Standard)
(1) XG Native Parameter Change
Control
0n
ccH
vvH
Data format: [F0H] -> [43H] -> [1nH] -> [4CH] -> [hhH] ->
Split Point
Metronome
Always 00H
Always 00H
14H
1BH
14H: Split Key Number
00H: No accent
[mmH] -> [
ll
H] -> [ddH] -> [F7H]
01H-0FH: 1/4-15/4
F0H = Exclusive status
7FH: off
43H = YAMAHA ID
Damper Level
ch: 00H-0FH
3DH (Sets the Damper Level
1nH = When received, n=0~F
for each channel)
When transmitted, n=0.
00H-7FH
4CH = Model ID of XG
Channel Detunech: 00H-0FH
43H (Sets the Detune value
hhH = Address High
for each channel)
mmH = Address Mid
00H-7FH
llH
=
Address Low
Voice Reserve
ch: 00H-0FH
45H
00H : Reserve off 7FH
ddH =
Data
: on*
l
F7H = End of Exclusive
Data size must match parameter size (2 or 4 bytes).
When the XG System On message is received, the MIDI sys
tem will be reset to its default settings.
The message requires approximately 50ms to execute, so
sufficient time should be allowed before the next message is
sent.
(2) XG Native Bulk Data (reception only)
Data format: [F0H] -> [43H] -> [0nH] -> [4CH] -> [aaH] ->
[bbH] -> [hhH] -> [mmH] ->
[llH]
->[ddH] ->...->
[ccH] -> [F7H]
F0H = Exclusive status
43H = YAMAHA ID
0nH = When received, n=0~F
When transmitted, n=0.
4CH = Model ID of XG
aaH =
ByteCount
bbH = ByteCount
hhH = Address High
mmH = Address Mid
llH =
Address Low
ddH =
l
Data
l
l
ccH =
l
Check sum
F7H = End of Exclusive
Receipt of the XG SYSTEM ON message causes reinitializa
tion of relevant parameters and Control Change values. Allow
sufficient time for processing to execute (about 50 msec)
before sending the CLP-240/230 another message.
XG Native Parameter Change message may contain two or
four bytes of parameter data (depending on the parameter
size).
For information about the Address and Byte Count values,
refer to Table 1 below. Note that the table's Total Size value
gives the size of a bulk block. Only the top address of the
block (00H, 00H, 00H) is valid as a bulk data address.
CLP-240/230 Руководство пользователя
9. SYSTEM EXCLUSIVE MESSAGES
(Clavinova MIDI Format)
Data format: [F0H] -> [43H] -> [73H] -> [01H] -> [nnH] -> [F7H]
F0H = Exclusive status
43H = Yamaha ID
73H = Clavinova ID
01H = Product ID (CLP common)
nnH = Substatus
nn Control
02H Internal MIDI clock
03H External MIDI clock
F7H = End of Exclusive
10.SYSTEM EXCLUSIVE MESSAGES (Special Control)
Data format: [F0H] -> [43H] -> [73H] -> [66H] -> [11H] ->
[0nH] -> [ccH] -> [vvH] -> [F7H]
F0H = Exclusive status
43H = Yamaha ID
73H = Clavinova ID
7FH = Extended Product ID
xxH = Product ID 49H
11H = Special control
0nH = Control MIDI change (n=channel number)
cc = Control number
vv = Value
F7H = End of Exclusive
* When Volume, Expression is received for Reserve On, they
will be effective from the next Key On. Reserve Off is normal.
11.
SYSTEM EXCLUSIVE MESSAGES (Others)
Data format: [F0H] -> [43H] -> [1nH] -> [27H] -> [30H] -> [00H]
-> [00H] -> [mmH] ->
[llH]
-> [ccH] -> [F7H]
Master Tuning (XG and last message priority) simultaneously
changes the pitch of all channels.
F0H = Exclusive Status
43H = Yamaha ID
1nH = When received, n=0~F
When transmitted, n=0.
27H = Model ID of TG100
30H = Sub ID
00H =
00H =
mmH = Master Tune MSB
llH = Master Tune LSB
ccH = don't care (under 7FH)
F7H = End of Exclusive