ZELMER 281 - Инструкция (Страница 67)

71
2 Insert the threaded part into the motor casing hole and
screw it turning right until you feel the refusal.
Inadequate screwing of the mixing adapter can result
in clutch damage or the adapter damage.
3
Put the adapter into the processed product and switch
the mixer on.
Operation with mixing cup (Fig. G)
CAUTION! Hold the mixer in your hand all the time
during operation.
Mixing cup is intended for infant soups preparation, milk
shakes or pancake dough.
It has the label „500 ml max” on both sides, which
●
indicates the maximum level of product to fill the cup and
graphic scale to determine the volume 200 ml to 500 ml
(according to the symbols in the drawing beside).
1 After moving the cover (like during assembling the
adapter) assemble the cup the following way: Insert the
mixing cup on the motor part so that the 3 buckles visible at
the bottom of the cup got into the nuts of the motor casing.
2 Holding the motor casing handle turn the cup clockwise
direction until you feel the refusal.
You shall obtain the proper connection, when the 3 buckles get
under the motor casing, and the fastener on the cup rib move
on the other side of the spherical buckle on the motor casing.
3 Fill the cup with products and put the cover with the doser
on – you can add next products to the cup during operation.
Operation with stand including turnable bowl (Fig. H)
The stand with assembled motor part makes the operation
with whisks or mixers easy, as the user does not have to hold
the device.
The stand head driver automatically makes the head move
pendulum-like and simultaneously turns the bowl with the
mixed product.
You can use the stand with specially prepared whisks and
mixers only. The device equipped with stand includes also
one mixer and one whisk with toothed bar.
1 Insert the mixers or whisks into the motor casing (as
described above).
2 Assemble the drive in the stand head after moving the
cover (like during assembling the adapter) the following way:
Insert the drive fasteners (which are located near the holes
for whisks assembling) under the stand head fastener.
3 Turn the control clamp to the limit in such a way that the
hand is positioned vertically.
4 Press the fastener button and simultaneously deflect the
stand head with the motor part back.
5 If the bowl with products a bit up and then insert it on the
three insertions and place it at the stand base.
6 Place the stand head with the motor part in horizontal
position (you will hear the clicking sound of fastener blocking
clamps).
The manufacturer does not accept any liability for any damages
resulting from unintended use or inappropriate handling.
The manufacturer reserves his rights for modifying the product any
time in order to adjust it to law regulations, norms, directives, or due
to construction, trade aesthetic or other reasons, without notifying it
in advance.
Start-up the mixer with the switch lever and it will make the
●
bowl turn and the head with drive move pendulum-like.
Never block or stop the oscillatory movement during
operation. It may cause damage to the housing.
After operation (Fig. I)
1 Switch the mixer off and unplug it.
Depending on assembled equipment:
2 Push the whisks or mixers out with a pushing button.
3 Disassemble the liquidizing disc from the whisk.
Disassemble the mixing adapter or mixing cup in reverse
●
way to assembling it.
4 Deflect the stand head with the motor part back.
5 Turn the clamp knob in counter clockwise direction
as much as possible and put the motor out of the head
fasteners.
6 Wind the power cord on the motor part and put the last
winding under the insert.
Cleaning and maintenance
Remember to unplug before clearing and maintenance.
Clean the whisks and mixers with warm water with
●
cleaning agents.
Clean the mixing adapter and mixing cup by mixing clean,
●
warm water (after plugging the mixer to mains supply).
Clean the cogged rim of rotational bowl with dishes
●
cleaning brush.
Do not wash the mixing adapter or the mixing cup in
●
dishwasher.
Turn the bowl upside down after cleaning and pour out
●
the water, which could remain under the cogged rim.
Dry the mixer equipment after cleaning and store in dry
●
place.
Clean the motor or stand casing with dump cloth and
●
then dry it.
Ecology – environment protection
Each user can protect the natural environment. It is neither
difficult nor expensive. In order to do it: Put the cardboard
packing into recycling paper container, Put
the polyethylene (PE) bags into container for
plastic.
When worn out, dispose the appliance to
particular disposal centre, because of the
dangerous elements of this appliance, which
can be hazardous for natural environment.
Please do not dispose into domestic waste disposal!!!