Listening through a receiver, Check points before requesting service – Инструкция по эксплуатации Samsung LE52A900G1F

Страница 57

Advertising
background image

english - 

listening through a receiver

You can listen to sound through a receiver instead of the tV speaker.

1. Press the toolS button. Then Press the enter button to select "Anynet+(HDMI-

CEC)".

Press the ▲ or ▼ button to select "Receiver", then press the

enter button.

. Press the ◄ or ► button to select to "On", then press the enter button.

Now you can listen to sound through the receiver.

. Press the eXIt button to exit.

When the receiver is set to On, you can listen to the TV sound through the 2-channel

receiver.

If the receiver is exclusively for a home theatre only (supporting audio only), it may not

appear in the device list.

Only when you have connected the optical jack of the TV and the receiver properly, does Receiver work.

In case of a content with copyright problem, listening through the receiver may not properly operate.

If there is a power interruption to the TV when the “Receiver” is set to “On” (by disconnecting the power cord or a power

failure), the “TV Speaker” may be set to “Off” when you turn the TV on again. (see page 21)

Check Points before requesting Service

Symptom

Solution

anynet+ does not work.

■ Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices only.

■ Connect only one receiver.

■ Check if the Anynet+ device power cord is properly connected.

■ Check the Anynet+ device’s Video/Audio/HDMI 1.3 cable connections.

■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.

■ Check whether the TV remote control is in TV mode.

■ Check whether it is Anynet+ exclusive remote control.

■ Anynet+ doesn’t work at a certain condition. (Searching channels, Operating WISELINK, Plug & Play,

etc.)

■ When connecting or removing the HDMI 1.3 cable, please make sure to search devices again or

restart your TV.

■ Check if the Anynet+ Function of Anynet+ device is set on.

I want to start anynet+.

■ Check if the Anynet+ device is properly connected to the TV and check if the Anynet+ (HDMI-CEC) is

set to On in the Anynet+ Setup menu.

■ Press the

tV/DtV button on the TV remote control to switch to TV. Then press the toolS button to

show the Anynet+ menu and select a menu you want.

I want to exit anynet+.

■ Select

View tV in Anynet+ menu.

■ Press the

SourCe button on the TV remote control and select a device other than Anynet+ devices.

■ Press any of

P /

and

Pre-Ch such to change to the TV mode. (Note that the channel button

operates only when a tuner-embedded Anynet+ device is not connected.)

the Configuring anynet+

connection message appears

on the screen.

■ You cannot use the remote control when you are configuring Anynet+ or switching to a view mode.

■ Use the remote control when the Anynet+ setting or switching to view mode is complete.

the anynet+ device does

not play.

You cannot use the play function when Plug & Play is in progress.

the connected device is not

displayed.

■ Check whether or not the device supports Anynet+ functions.

■ Check whether or not the HDMI 1.3 cable is properly connected.

■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.

■ Search Anynet+ devices again.

■ You can connect an Anynet+ device using the HDMI 1.3 cable only. Some HDMI cables may not

support Anynet+ functions.

■ If it is terminated by an abnormal situation such as disconnecting the HDMI 1.3 cable or power cord

or a power failure, please repeat the device scan.

the tV programme cannot be

recorded.

Check whether the antenna jack on the recording device is properly connected.

the tV sound is not output

through the receiver.

Connect the optical cable between TV and the receiver.

View tV

Select Device

record

menu on Device

Device operation

receiver

:off

Setup

tV

P

move

enter

return

BN68-01625C-01Eng.indd 54

2008-08-19 �� 10:11:26

Advertising
Эта инструкция подходит к следующим моделям: