Marantz PM6003 - Инструкция (Страница 17)

12
NAMES AND FUNCTIONS
BASIC
CONNECTIONS
BASIC
OPERA
TION
ADV
ANCED
CONNECTION
REMOTE CONTROLLER
OPERA
TION
TROUBLESHOOTING
OTHERS
REMOTE CONTROLLER
OPERA
TION
TROUBLESHOOTING
ENGLISH
REMOTE CONTROLLER OPERATION
REMOTE CONTROL CODE
SETTING
x
z
c
The remote control unit contains 3 sets of remote
control codes, and it can be used to control up to
3 amplifi ers in one location. To control a second
or third amplifi er, select the remote control code
as explained below. The selected amplifi er can be
operated from the remote control.
• When the unit is shipped from the factory, the
main unit and remote control are set to AMP1.
1.
AMP2
To set the remote control to AMP2, hold
down both the AMP button z and 2 number
button x on the remote control for at least
fi ve seconds.
AMP3
To set the remote control to AMP3, hold
down both the AMP button z and 3 number
button x on the remote control for at least
fi ve seconds.
2. Also set the main unit's remote control
setting to the same setting as the remote
control.
3. To change main unit's remote control
setting, hold down the AMP button z
and press the DISPLAY button c on the
remote control; the remote control setting
will be indicated by function indicators on
the main unit and main unit setting will be
changed same setting as remote control.
AMP1 : PHONO indicator blink 3 times.
AMP2 : TUNER indicator blink 3 times.
AMP3 : CD indicator blink 3 times.
Note
• If the main unit is unplugged the mains cord, the
remote control setting will revert to AMP1.
• To set the remote control back to AMP1, hold
down both the AMP button z and 1 number
button x on the remote control for at least fi ve
seconds.
TROUBLESHOOTING
In case of trouble or abnormal operation of the unit, check the following before contacting service personnel.
What may seem to be a serious malfunction is often the result of a simple operation mistake. If the trouble
persists after checking the following, please contact your dealer or nearest Marantz distributor.
* The amplifi er does not operate and the
indicators do not light.
1. Check to see if the power cable is inserted
properly into the power outlet.
* The indicators light but the amplifier
does not operate.
1. Check to see if the SELECTOR, SPEAKER
switches and VOLUME control are properly
set.
* Sound is heard from only one of the
speakers.
1. Check to see if the BALANCE control is
properly set.
2. Switch the power of the unit to OFF, and
change the connections of the left and right
speaker cords. If the sound from the same
speaker is still not heard, its connection
cord or the speaker itself may be defective.
* Considerable hum noise is heard when
the turntable is played.
1. Check to see if the plugs from the turntable
are properly connected to the PHONO
jacks.
2. Connect the grounding wire of the turntable
to the GND terminal on the rear panel of
this unit. If it has already been connected,
try removing it.
3. Check to make sure that the phono cartridge
is attached securely to the tonearm.
4. Unplug the power cable and plug it in
again after inverting the orientation of the
blades.
* Remote control operation is not possible.
1. Is the remote controller's transmitter
pointed correctly at the remote sensor on
the front of the Amplifi er?
Or, is there an obstruction between the
transmitter and the remote sensor?
2. Are the batteries in the remote controller
exhausted?
3. Is there another strong light (from a window,
etc.) striking the Amplifi er remote sensor?
4. Is an RCA cord connected to the “REMOTE
CONTROL OUT” jack on the Amplifi er rear
panel?
5. Is the remote control code different between
the main unit and remote controller?
6. Is the main unit remote sensor disabled?
PM6003_N_01_Eng_New.indd 12 PM6003_N_01_Eng_New.indd 12 09.4.20 3:57:55 PM 09.4.20 3:57:55 PM