Kastor TS Fireplace inserts - Инструкция (Страница 18)

2/08
Art nr K0006123
17
5.6. ADJUSTING COMBUSTION AND POWER OF
THE INSERT
Power of the insert can be adjusted in three ways:
1) by regulating the draught in the chimney. By means
of the damper in the chimney, the draught can, if
necessary, decreased so that the flames cannot
enter the chimney, which makes it possible to
regulate the fireplace more easily by means of the
air flow regulator located under the door. Watch
out for carbon monoxide !!!
2) by means of the adjustable fire-grate (not available
for models TS-12 and -21). The grate open: intense
combustion, the grate closed: low combustion. The
intensity of combustion can be increased by
opening the ash box.
On models TS-12 ja 21 there is a knob below the
door for regulating the primary air (for full air flow
turn the knob to the right).
3) by changing the quantity or quality of wood. Usually
there is no need to burn more than 4 billets of
firewood at the same time, irrespective of their
size. Thick billets, of course, will burn for a longer
time. On the other hand, dry wood releases heat
more and more quickly than moist wood. Very dry
firewood must be burnt carefully - its
momentary power is very high!
A firewood of good quality gives up heat much more
efficiently than, for example rotten or wet wood.
The smoke damper must not be closed, if there is
fire or embers in the fireplace insert. Risk of
inhaling carbonmonoxide!!!
5.7. GLASS DOORS - USE AND MAINTENANCE
The glasses must be cleaned when they are cold, using
a suitable cleaning agent. Although the doors are made
of special glass, handle them with care (avoid impacts
on the doors and do not slam the doors etc.).
Do not turn the doors too much in their opening
direction - it can damage the hinges, wrench the door
in a wrong position and brake the glass.
5. 8 REPLACING THE GLASSES
Models TS-36, -12, -21, -56, -57 have a fixed glass
fitted in the frame. To replace the glass, the whole door
must be replaced.
Replacing the door, models TS-36 ja 12:
• Open the door to its limit.
• Lift the door upwards to detach it from its hinges.
Attach in reverse order.
Replacing the door, model TS-21. See section 3.4.1
for changing the opening direction.
Model TS-26: for this model only the glasses can be
replaced as follows:
• Remove the broken pieces of glass and detach the
door.
• Open the door approx. 90 0 .
• Lift the door upwards from the hinge side.
• Pull the lower side of the frame outwards to release
the pin from its hole.
• Lower the door to release also the pin on the upper
part from its hole.
• Attach in reverse order.
Replacing the glass (fig. 6)
• Using, for example a screwdriver, push the locks 1
on the inner side of the frame from the right, from
the left and from above down against the frame.
• To detach the glass mouldings and the sealing tape
3 push the glass mouldings 2 located on the sides
and on the upper side towards the edges of the
frame. Do not remove the moulding and the sealing
on the lower side of the frame.
• Remove the possible broken pieces of glass from
the lower moulding.
• The new glass is fitted in reverse order. The sealing
tape 3 must be fitted around the bottom of the glass
mouldings and, in the corners, it should go under
the glass.
• Lastly, lift up the locks 1.
Replacing the glass, model TS-77:
• Holding the door firmly with the other hand,
open the door 90 0 , loosen the screw on the
uppermost hinge (fig. 7 part 1), lift the hinge against
the upper plate and remove the door from the hinge
pin.
• Place the door on a level surface the inner side
upwards, loosen the latch screw and the support
plate (fig. 8 parts 2 and 5).
• Remove the screws on the end mouldings (fig. 7
part 2).
• Remove the end molding (fig. 11 part 3).
• Remove the pieces of glass from the mouldings and
the door body.
• Turn the door the outer side upwards.
• There must be a sealing tape on the both sides of
the edge (fig. 11 part 5).
• Place the glass in the middle of the door and fix the
end mouldings with screws and fit the latch.
• Lift the door in place and fix the hinge with the
screw.
Replacing the glasses, model TS-56 and 57
We recommend replacing the glasses with the frames.
The smaller side glasses with their frames are
detachable.
At first lift the glass upwards (using, for example a
screwdriver) to release the bottom pins from their holes.
• Pull the lower side towards you.
• Lower the glass to release the pins on the upper
part from their holes.
• Fit new glasses in reverse order.
The door is replaced in the following manner:
• Open the door.
• Lift the door to release it ftom the hinge pins
• Replacement in reverse order.
• If necessary, align the new door with the frame by
bending the hinges.
5.9. MAINTENANCE OF THE SURFACE
The next steps shall be taken only when the fireplace is
cold. Remove regularly dust from the surfaces of the
insert using a soft cloth. Use only a mild detergent, for