Инструкция по эксплуатации Indesit KN3C767A(X)-RU
Страница 22
22
GB
Planning cooking with the electronic
programmer
Setting the clock
After the appliance has been connected to the
power supply, or after a powercut, the clock display
will automatically reset to 0:00 and begin to blink.
To set the time:
1. Press the COOKING TIME button
$
$
$
$
$
and the
COOKING END TIME
%
%
%
%
%
simultaneously.
2. Within 4 seconds of having pressed these
buttons, set the exact time by pressing the
*
*
*
*
*
and
)
)
)
)
)
buttons. The
*
*
*
*
*
button advances the hours and
the
)
)
)
)
)
button decreases the hours.
Once the time has been set, the programmer
automatically switches to manual mode.
Setting the timer
The timer enables a countdown to be set, when the
time has elapsed a buzzer sounds.
To set the timer proceed as follows:
1. press the TIMER button
H
H
H
H
H
. The display shows:
N
2. Press the
*
*
*
*
*
and )
)
)
)
) buttons to set the desired
time.
3. When the buttons are released the timer begins
counting down and the current time appears on the
display.
R
4. After the time has elapsed a buzzer will sound,
and this can be switched off by pressing any button
(except the
*
*
*
*
*
and
)
)
)
)
)
buttons). The symbol
H
H
H
H
H
will
switch off.
!!!!! The timer does not switch the oven on or
The timer does not switch the oven on or
The timer does not switch the oven on or
The timer does not switch the oven on or
The timer does not switch the oven on or
o f f .
o f f .
o f f .
o f f .
o f f .
Adjusting the volume of the buzzer
After selecting and confirming the clock settings,
use the
)
)
)
)
)
button to adjust the volume of the alarm
buzzer.
Setting the cooking time with a delayed start
First decide which cooking mode you wish to use
and set a suitable temperature using the SELECTOR
and THERMOSTAT knobs on the oven.
At this point it is possible to set the cooking time:
1. Press the COOKING TIME button
$
$
$
$
$
.
2. Within 4 seconds of having pressed this button,
set the desired amount of time by pressing the
*
*
*
*
*
and
)
)
)
)
)
buttons. If, for example, you wish to set a
cooking time of 30 minutes, the display will show:
N
3. 4 seconds after the buttons are released, the
current time (for example 10.00) reappears on the
display with the symbol
m
m
m
m
m
and the letter A (AUTO).
Next the desired cooking end time must be set:
4. Press the END COOKING TIME button
%
%
%
%
%
.
5. Within 4 seconds of having pressed this button,
adjust the cooking end time by pressing the
*
*
*
*
*
and
)
)
)
)
)
buttons. If, for example, you want cooking to end
at 13.00, the display shows:
O
6. 4 seconds after the buttons are released, the
current time (for example 10.00) reappears on the
display with the letter A (AUTO).
P
At this point, the oven is programmed to switch on
automatically at 12:30 and switch off after 30 minutes,
at 13.00.
Setting the cooking time with an immediate start
Follow the above procedure for setting the cooking
time (points 1-3).
!When the letter A appears, this indicates that both
the cooking time and the end cooking time have been
programmed in AUTO mode. To restore the oven to
manual operation, after each AUTO cooking mode
press the COOKING TIME
$
$
$
$
$
and END COOKING
TIME
%
%
%
%
%
buttons simultaneously.
!The symbol
m
m
m
m
m
will remain lit, along with the oven,
for the entire duration of the cooking programme.
The set cooking duration can be displayed at any
time by pressing the COOKING TIME button
$
$
$
$
$
, and
the cooking end time may be displayed by pressing
the END COOKING TIME button
%
%
%
%
%
. When the
cooking time has elapsed a buzzer sounds. To stop
it, press any button apart from the
*
*
*
*
*
and
)
)
)
)
)
buttons.
Cancelling a previously set cooking programme
Press the COOKING TIME button
$
$
$
$
$
and the
COOKING END TIME
%
%
%
%
%
simultaneously.
Correcting or cancelling previously set data
The data entered can be changed at any time by
pressing the corresponding button (TIMER,
COOKING TIME or COOKING END TIME) and the
*
*
*
*
*
or
)
)
)
)
)
button.
When the cooking time data is cancelled, the cooking
end time data is also cancelled automatically, and
vice versa.
If the oven has already been programmed, it will not
accept cooking end times which are before the start
of the programmed cooking process.