Vitek VT-4120 SR - Инструкция (Страница 8)

ENGLISH
8
System setup
1. Switch TV-set on and select the adequate type of input signal in TV-
set settings.
Press SETUP button to enter system setup menu. Press SETUP
button again to exit menu.
. Use navigation buttons ( ←→) to select on of the next pages: main
setup page, audio setup page, video setup page, custom setup
page, password setup page.
. Press button ( ↓) to enter selected page.
4. Use buttons ( ↓↑) to select an item you want to change.
5. Press button ► or → to enter sub-item to change a setting. Use
navigation buttons ( ↓↑) to select required value ► or ← to confirm
selected value and return to list of settings.
Attention: some menu items corresponding to preset modes are
marked and cannot be selected.
Input settings are stored even after switching off power.
Main setup page
TV screen
4:/PS: When DVD player is connected to normal TV-set, wide screen
picture is viewed on the whole screen, but its side parts are cut (4:).
4:/LB: When DVD player is connected to normal TV-set, wide screen
picture is viewed thus there are black regions in upper and down part of
the screen (4:).
Wide screen: use this item if home theater is connected to wide screen
TV-set (16:9).
View angle
Some DVD movie could be shot from different angles. Detailed
information concerning this subject you can get from annotation to your
DVD disk.
If this mode is on while playing back DVD disk shot from different angles
symbol of camera is displayed on the screen.
Menu language
Selecting on-screen menu language.
Subtitles
This function is not working if there are no subtitles recorded on a disk. If
disk’s subtitle function if switched off, press SUBTITLE button on remote
control to switch it on. Default setting is ON.
Screensaver
If screensaver function is on, player is switched on, but disk is not
playing back for several minutes, a moving picture is appeared on the
screen, after 0 minutes player is switched to standby mode. You can
press button STANBY on remote control to exit standby mode.
Last memory
If this function is on, layer remembers the time of disk’s taking out, the
next time you load the same disk, player will play it from the place of last
stop and extraction of the disk.
Audio setup page
• Setup speakers
- Downmix
Left/Right: original sound in 5.1 CH format is transferred through left and
right channel only.
Stereo: original sound in 5.1 CH format is transferred in stereo mode.
D surround: effect of D surround sound is created using two channels
only.
5.1 CH: original sound in 5.1 CH format is transferred through 5
channels: front, central, rear speakers, subwoofer.
If your sound system includes front, central, rear speakers and
subwoofer, you can set menu items according to real configuration. This
function would not work if fading function is on (left/right, stereo, d
surround).
Test signal
In 5.1CH audio mode select ON (switch test signal on), test signal will
be played through all six channel in sequence. Setting the system up
by test signal is to be done on condition there is no disk in the tray and
parameter FADE is set to “5.1СН” position.
Use this function to examine all audio channels if you are in doubt about
the quality of sound.
Dynamic compression (Post DRC)
Dynamic range compression allows decreasing sudden volume jumps
caused by sound effects. You can switch compression on (ON) or off
(OFF) or select automatic mode (AUTO). Post DRC is inactive when
downmix is setr 5.1.
• Digital output setup page
- Digital output
Switch off SPDIF: sound is supplied to appliance output in analog form
(5.1 CH AUDIO OUT).
SPDIF/RAW: digital output signal in original format as recorded on disk.
SPDIF/PCM: digital output signal in decoded РСМ format.
- LPCM output
Select setting for audio format: 48 К, 96 К.
4120IM.indd 8 20.02.2008 10:24:28