ZELMER 480 - Инструкция (Страница 79)

83
3 Plug the power cord to the power supply socket.
4 Plunge the end of the whisk inside the beaker into
products.
5 Then start – up the appliance pressing the switch
and set the required gear as necessary.
Operational guidelines
To detach the whisk attachment, just follow the attaching
●
procedure in reverse order.
For best results operate the appliance at high gear –
●
12th speed setting.
The working time of the blender with whisk attachment
●
can not exceed 3 minutes. Before reusing, the drive shaft
must cool.
When finished, turn the appliance off and unplug it by
●
disconnecting the cable cord from the power outlet.
You can also use the mixing container included with the
●
blender.
ATTENTION! To obtain better results lean the whisk
is a small angle and make round movements with it
inside the bowl.
OPERATING THE MINI FOOD PROCESSOR (Fig. E)
ZELMER hand blender is equipped with a mini food
processor used to chop meat, cheese, nuts, onions, garlic,
carrots, and prunes.
ATTENTION! Before assembling on and removing the
blender drive out of the mini food processor, make sure
that the plug of the supplying cord is disconnected
from the mains supply outlet.
Wash the parts in contact with processed product before
first usage.
Operate the blender so, that the closed/open marking
located on the appliance are well visible.
Before each usage of the mini food processor knife,
●
remove the cover out of the blades.
1 Insert the blade into the container so that the protrusion
of the container fits the opening in the blade.
2 Put the food to be processed into the container. Fill in the
container. Do not exceed the marked MAX level.
3 Put the cover�transmission on the container. Make sure
the protrusions fit the openings in the container and turn the
lid clockwise until stop.
4 Place the blender motor in open position on such
assembled mini food processor, in accordance with the
indicator on the motor casing and the lid of the mini food
processor including gearbox.
5 Turn the motor clockwise relative to the transmission
(according to the direction of the arrow) until you hear a click
(the indicator on the transmission should be in the closed
position ).
6 Plug in the appliance.
7 Switch on the appliance pressing the switch .
8 Set the required gear as necessary.
ATTENTION! The mini food processor blades are
very sharp. Be very careful during assembling,
disassembling or during cleaning. Store the knife
inside the cover for safety reasons.
ATTENTION! It is not allowed to grind too hard
products, such as: coffee beans, nutmeg, ice cubes.
ATTENTION! Before shredding big pieces of the
products cut them into smaller ones – approximately
1 cm cubes.
ATTENTION! Never disassemble the lid from the
container before the disc stops rotating.
Operational guidelines
The dismantling process should be done in reverse order
●
to assembly.
The operating time of the blended equipped with the food
●
processor cannot exceed 2 minutes. Allow the motor to
cool before proceeding.
Do not start – up the motor without accessories.
●
When finished, turn the appliance off and unplug it by
●
disconnecting the cable cord from the power outlet.
If the products stick to the blade or the walls of the
●
container:
Switch off the appliance. –
Remove the drive with the lid and container of ice or –
other products crusher.
Remove the products out of the mini food processor –
walls.
Re�assemble the appliance – as defined above, –
Continue the operation.
Approximate time for processing of selected
products for the recommended gear
Product
Recommended
gear
Processing
time
TURBO 20�30 s
TURBO 25�30 s
1/4
8 15 s
12
+TURBO
40 s + 5 s
300 g
(500 ml)
250 g
(500 ml)
200 g
(500 ml)
1 cm
1 cm
250�300 g
(400�500 ml)