Panasonic SC-AK410 - Инструкция (Страница 25)

Using the timers
SLEEP-
* _ «' 6«
-O Q CB-
1 • 2@ • 3i
^"^1— 2® • 3©
1 • 2® • 3® • 4 —^
Using the piay/record timer
Remote control only
You can set the timer to come on at a certain time to wake you up
(play timer) or to record a radio station or from the aux source (record
timer).
The play and record timers cannot be used together.
Preparations:
• Turn the unit on and set the clock (-♦ page 17).
• For the play timer, prepare the desired music source (tape/CD/
radio/aux), and set the volume.
• For the record timer, check the cassette’s erasure prevention tabs
(-*• page 16) and insert the tape in deck 2 (^ page 15). Tune to
the radio station {-*■ page 14) or select the aux source page
16).
1 Press [SHIFT] + [CLOCK/TIMER] to select the timer
function.
Every time you press the button:
CLOCK-- ©PLAY -- ©REC
t— Previous display <—I
©PLAY: to set the play timer
©REC: to set the record timer
ON time setting
® (Within 8 seconds or so)
Press [!◄◄, REW/V] or [
start time.
(D Press [SHIFT] + [CLOCK/TIMER].
, A/FF] to set the
OFF time setting
® Press [!◄◄, REW/V] or [►►!, A/FF] to set the
finish time.
(D Press [SHIFT] + [CLOCK/TIMER].
The start and finish times are now set.
Press [SHIFT] + [©PLAY/REC] to display the timer
indicator.
Every time you press the button:
©PLAY — © R E C
©PLAY: to turn the play timer on
©REC:
to turn the record timer on
(The indicator doesn’t appear if the start and finish times or the
clock hasn’t been set.)
Press [©] to turn the unit off.
The unit must be off for the timers to operate.
• Play timer:
Play will start in the set condition at the set time
with volume increasing gradually to the set level.
• Record timer: The unit comes on 30 seconds before the set
time with the volume muted.
To cancel the timer
Press [SHIFT] + [©PLAY/REC] to clear the timer indicator from the
display.
(The timer comes on at the set time everyday if the timer is on.)
To change the settings (when the unit is on)
To change the piay/record times
Do steps 1, 2, 3 and 5.
To change the source or volume
1. Press [SHIFT] + [©PLAY/REC] to clear the timer indicator from the
display.
2. Make changes to the source or volume.
3. Do steps 4 to 5.
To change the timer
Press [SHIFT] + [©PLAY/REC] to select the desired timer.
Every time the button is pressed:
©PLAY — ©REC
t ------ (off) -- ------ 1
To check the settings
Press [SHIFT] + [CLOCK/TIMER] while the unit is on to select “©PLAY”
or “©REC”.
The settings are shown in the following order:
Play timer: start time^finish time^source^volume
Record timer: start time-^finish time~>source
To check the settings while the unit is off, press [SHIFT] + [CLOCK/
TIMER] twice.
If you use the unit after the timers are set
After using, check that the correct tape/CD are loaded before turning
the unit off.
• if you turn the unit off and on again while a timer is functioning, the
finish time setting will not be activated.
• If you selected AUX as the source, when the timer comes on, the
unit turns on and engages “AUX” as the source. If you want to
playback or record from a connected unit, set that unit’s timer to the
same time. (See the connected unit’s instruction manual.)
Using the sleep timer
Remote control only
This timer turns the unit off after a set time.
While enjoying the desired source:
Press [SLEEP] to select the time (minutes).
Every time you press the button:
SLEEP 30 -► SLEEP 60 — SLEEP 90 -► SLEEP 120 -► SLEEP OFF -
To cancel the sleep timer
Press [SLEEP] to select “SLEEP OFF”.
To confirm the remaining time
Press [SLEEP] once.
The remaining time is shown for about 5 seconds.
To change the setting
Press [SLEEP] to select the new setting.
You can use the sleep timer in combination with the piay/record timer.
Make sure the unit is off before the piay/record timer’s start time.
The sleep timer will be turned off when you start recording trom a CD.