Installation, Before installing this unit, Installation with the holder and side bracket – Инструкция по эксплуатации Pioneer AVH-P4200DVD

Страница 4: Installing the microphone (avh-p3200bt only), Adjusting the microphone angle, When installing the microphone on the sun visor

Advertising
background image

Note

• Check all connections and systems before final

installation.

• Do not use unauthorized parts as this may cause

malfunctions.

• Consult your dealer if installation requires drilling of

holes or other modifications to the vehicle.

• Do not install this unit where:

— it may interfere with operation of the vehicle.

— it may cause injury to a passenger as a result of

a sudden stop.

• Do not install the display where it may (i) obstruct

the driver’s vision, (ii) impair the performance of

any of the vehicle’s operating systems or safety

features, including air bags, hazard lamp buttons or

(iii) impair the driver’s ability to safely operate the

vehicle.

• The semiconductor laser will be damaged if it

overheats. Install this unit away from hot places

such as near the heater outlet.

• Optimum performance is obtained when the unit is

installed at an angle of less than 30°.

• When installing, to ensure proper heat dispersal

when using this unit, make sure you leave ample

space behind the rear panel and wrap any loose

cables so they are not blocking the vents.

Before installing this unit

Remove the holder.

Loosen the screws (3 × 6 mm) to remove the

holder.

Screw (3 × 6 mm)

(Supplied with this unit)

Holder

(Supplied with this unit)

Installation with the holder

and side bracket

1. Install the holder into the dashboard.

After inserting the holder into the dashboard,

select and bend the tabs appropriate to the

thickness of the dashboard material. (Install

this unit as firmly as possible using the top and

bottom tabs. To secure this unit, bend the tabs

90 degrees.)

Dashboard

Holder(Supplied with this unit)

2. Install this unit and fasten the screws.

Rubber bush

(Supplied with this unit)

Double-ended screw

(Supplied with this unit)

Screw (3 × 6 mm)

(Supplied with this unit)

Dashboard

3. Attach the trim ring.

Trim ring

(Supplied with this unit)

Installation using the screw

holes on the side of the unit

1. Remove the side brackets.

Side bracket

(Supplied with this unit)

Screw for fixing the side

bracket (5 × 9 mm)

(Supplied with this unit)

2. Fastening the unit to the factory

radio-mounting bracket.

Position the unit so that its screw holes are

aligned with the screw holes of the bracket, and

tighten the screws at 3 or 4 locations on each

side.

Factory radio mounting bracket

If the pawl gets in the way,

bend it down.

Dashboard or console

Tapping screw

(5 × 8 mm)

Note

In some types of vehicles, discrepancy may

occur between the unit and the dashboard. If this

happens, use the supplied frame to fill the gap.

Installing the microphone

(AVH-P3200BT only)

Installation notes

Install the microphone in a position and
orientation that will enable it to pick up the voice
of the person operating the system.

CAUTION

• It is extremely dangerous to allow the microphone

lead to become wound around the steering column

or gearstick. Be sure to install the unit in such a

way that it will not obstruct driving.

When installing the microphone
on the sun visor

1. Install the microphone on the

microphone clip.

Microphone

Microphone clip

Microphone base

2. Install the microphone clip on the sun

visor.

• With the sun visor up, install the microphone

clip. (Lowering the sun visor reduces the voice

recognition rate.)

Microphone clip

Clamp

Use separately sold

clamps to secure the

lead where necessary

inside the vehicle.

When installing the microphone
on the steering column

1. Install the microphone on the

microphone clip.

Microphone

Microphone clip

Fit the

microphone lead

into the groove.

• Microphone can be installed without using

microphone clip. In this case, detach the

microphone base from the microphone clip. To

detach the microphone base from microphone

clip, slide the microphone base.

Installation

Installation

Installation

Installation

2. Install the microphone clip on the

steering column.

Double-sided tape

Install the microphone clip on the

rear side of the steering column.

Clamp

Use separately sold

clamps to secure the

lead where necessary

inside the vehicle.

Adjusting the microphone

angle

The microphone angle can be adjusted.

Leave ample space

Dashboard

Advertising
Эта инструкция подходит к следующим моделям: