Инструкция по эксплуатации Pioneer AVH-P4200DVD

Installation manual руководство по установке, Connecting the units, When connecting to separately sold power amp

Advertising
background image

Installation Manual

Руководство по установке

DVD RDS AV RECEIVER

DVD RDS AV РЕСИВЕР

AVH-P4200DVD
AVH-P3200BT

WARNING

• To avoid the risk of accident and the potential

violation of applicable laws, the front DVD or TV

(sold separately) feature should never be used

while the vehicle is being driven. Also, rear displays

should not be in a location where it is a visible

distraction to the driver.

• In some countries or states the viewing of images

on a display inside a vehicle even by persons

other than the driver may be illegal. Where such

regulations apply, they must be obeyed and this

unit’s DVD features should not be used.

CAUTION

• PIONEER does not recommend that you install

or service your display yourself. Installing or

servicing the product may expose you to risk

of electric shock or other hazards. Refer all

installation and servicing of your display to

authorized Pioneer service personnel.

• Secure all wiring with cable clamps or

electrical tape. Do not allow any bare wiring to

remain exposed.

• Do not drill a hole into the engine compartment

to connect the yellow lead of the unit to

the vehicle battery. Engine vibration may

eventually cause the insulation to fail at

the point where the wire passes from the

passenger compartment into the engine

compartment. Take extra care in securing the

wire at this point.

• It is extremely dangerous to allow the display

lead to become wound around the steering

column or gearshift. Be sure to install the

display in such a way that it will not obstruct

driving.

• Make sure that wires will not interfere with

moving parts of the vehicle, such as the

gearshift, parking brake or seat sliding

mechanism.

• Do not shorten any leads. If you do, the

protection circuit may fail to work properly.

WARNING

LIGHT GREEN LEAD AT POWER CONNECTOR

IS DESIGNED TO DETECT PARKED STATUS

AND MUST BE CONNECTED TO THE POWER

SUPPLY SIDE OF THE PARKING BRAKE SWITCH.

IMPROPER CONNECTION OR USE OF THIS LEAD

MAY VIOLATE APPLICABLE LAW AND MAY RESULT

IN SERIOUS INJURY OR DAMAGE.

Important

• This unit cannot be installed in a vehicle without

ACC (accessory) position on the ignition switch.

ACC

ON

S

T

A

R

T

O

FF

ON

S

T

A

R

T

O

FF

ACC position

No ACC position

• Use of this unit in conditions other than the

following could result in fire or malfunction.

— Vehicles with a 12-volt battery and negative

grounding.

— Speakers with 50 W (output value) and 4 ohm to

8 ohm (impedance value).

• To prevent short-circuit, overheating or malfunction,

be sure to follow the directions below.

— Disconnect the negative terminal of the battery

before installation.

— Secure the wiring with cable clamps or adhesive

tape. Wrap adhesive tape around wiring that

comes into contact with metal parts to protect

the wiring.

— Place all cables away from moving parts, such

as gear shift and seat rails.

— Place all cables away from hot places, such as

near the heater outlet.

— Do not connect the yellow cable to the battery

by passing it through the hole to the engine

compartment.

— Cover any disconnected cable connectors with

insulating tape.

— Do not shorten any cables.

— Never cut the insulation of the power cable of

this unit in order to share the power with other

devices. The current capacity of the cable is

limited.

— Use a fuse of the rating prescribed.

— Never wire the speaker negative cable directly to

ground.

— Never band together negative cables of multiple

speakers.

• When this unit is on, control signals are sent

through the blue/white cable. Connect this cable to

the system remote control of an external power amp

or the vehicle’s auto-antenna relay control terminal

(max. 300 mA 12 V DC). If the vehicle is equipped

with a glass antenna, connect it to the antenna

booster power supply terminal.

• Never connect the blue/white cable to the power

terminal of an external power amp. Also, never

connect it to the power terminal of the auto

antenna. Doing so may result in battery drain or a

malfunction.

• IP-BUS connectors are color-coded. Be sure to

connect connectors of the same color.

• The black cable is ground. Ground cables for

this unit and other equipment (especially, high-

current products such as power amps) must be

wired separately. If they are not, an accidental

detachment may result in a fire or malfunction.

<KOMNX> <09L00000>

Printed

in

Thailand

Отпечатано в Таиланде

<CRD4451-A/N> UW

When connecting to separately sold power amp

Blue/white
Connect to system control
terminal of the power amp
(max. 300 mA 12 V DC).

Blue/white (6*)
Connect to auto-antenna
relay control terminal
(max. 300 mA 12 V DC).

The pin position of the ISO connector will differ
depending on the type of vehicle. Connect 5*
and 6* when Pin 5 is an antenna control type. In
another type of vehicle, never connect 5* and 6*.

Blue/white (5*)

Connect with RCA cables
(sold separately)

Rear speaker

Perform these connections when
using the optional amplifier.

System remote control

Front speaker

Front speaker

Left

Right

Rear speaker

Power amp
(sold separately)

Power amp
(sold separately)

Power amp
(sold separately)

Subwoofer

Subwoofer

To front output

To rear output

To subwoofer
output

This product

Rear output

Front output

Subwoofer output

(AVH-
P4200DVD
only)

•When you connect the separately sold

multi-channel processor (DEQ-P6600) to this
unit, do not connect anything to the speaker
leads and system remote control (blue/white).

•When you connect the multi-channel

processor to this unit, refer to multi-channel
processor’s installation manual for the
connection method.

Connecting the units

Connecting the units

Connecting the units

Advertising
Эта инструкция подходит к следующим моделям: