Инструкция по эксплуатации Saturn ST-HC7387

Страница 3

Advertising

BLADE LEVER

The lever is conveniently located

near your thumb (If you’re right-

handed), so it can easily be ad-

justed while the clipper is in your

hand.

The lever adds versatility to your

clipper by allowing you to gradu-

ally change the closeness of your

cut without an attachment

comb.

When the lever is in the upper-

most position, the blades will

give you the closest cut and

leave the hair very short. Push-

ing the lever downward gradual-

ly increases the cutting length.

In its lowest position, the lever

will leave the hair approximately

the same length as a No. 1

comb.

The lever will also extend the

use of your blades, since a dif-

ferent cutting edge is used in

each setting.

In addition, if extremely heavy

hair cutting has jammed the

blades, it will help you remove

hair that has become wedged

between the two blades without

removing the blades.

While the clipper is running, rap-

idly move the lever from “close

cut” to “longer cut” a couple of

times. Doing this each time after

you have finished using your

clipper, will help to keep the

blades clear of cut hair. If your

clipper stops cutting and this

does not help, your cutting

blades are blunt. Replace them

with new blades.

IMPORTANT SAFEGUARDS

When using electrical appliances,

especially when children are pre-

sent, basic safety precautions

should always be followed, in-

cluding the following:

To reduce the risk of death or injury from

electric shock:

Unplug this appliance before

cleaning.

Do not place or store appliance,

where it can fall or be pulled into

a tub or sink.

Do not use, while bathing or in a

shower.

Do not place in or drop into wa-

ter or other liquid.

Do not reach for an appliance

that has fallen into water. Un-

plug immediately.

To reduce the risk of burns, electrocution,

fire or injury to persons.

Use this appliance only for its in-

tended use, as described in this

manual. Do not use attach-

ments, not recommended by the

manufacturer.

This appliance should never be

left unattended, when plugged

in.

Close supervision is necessary,

when this appliance is used by,

on or near children or invalids.

Never operate this appliance, if

it has a damaged cord or plug, if

it is not working properly.

Keep the cord away from heated

surfaces.

Do not pull, twist or wrap line

cord around appliance.

Never drop or insert any object

into any opening on this appli-

ance.

Before use, make certain blades

are aligned properly.

Do not place appliance on any

surface, while it is operating.

Do not use this appliance with a

damaged or broken comb nor

with teeth missing from the

blades, as injury may occur.

INSTRUCTIONS FOR HAIR CUTTING

Before starting the hair cut:

Inspect the clipper, making sure

that it is free of oil between the

cutting blade teeth and turn the

unit on to distribute the oil and

to make sure it is running

smoothly. Wipe off any excess

oil. This should be done after

each use. While using the unit,

untwist the cord from time to

time to avoid tangling.

Seat the person so their head is

approximately at your eye level.

This allows ease of visibility,

while cutting and a relaxed con-

trol of the unit.

Before cutting always first comb

the hair, so it is tangle free and

as it is naturally worn.

Place a towel around the neck

and shoulders of the person hav-

ing the haircut.

REMINDERS

Cut the hair in a relaxed

and slow manner. Use

short strokes only to

work gradually over the

entire head.

Always take off a little

hair at a time, you can

always trim off addi-

tional hair later.

As you work, comb the

hair frequently back in-

to the style to which

you are cutting.

When cutting with this

hair clipper, it is better

to leave the hair dry,

not wet. With the hair

dry, it is much easier to

control the amount of

hair being cut.

BEGINNING THE HAIRCUT

Cutting hair requires practice, so it is

always better to leave the hair longer for

the first few haircuts, until you become

used to the length, to which each at-

tachment cuts the hair.

ATTACHMENT COMB (see main dia-

gram)

Attachment Comb No. 1 leaves

3mm (1/8 inch) hair length.

Attachment Comb No. 2 leaves

6mm (1/4 inch) hair length.

Attachment Comb No. 3 leaves

9mm (3/8 inch) hair length.

Attachment Comb No. 4 leaves

12mm (1/2 inch) hair length.

Each comb attachment is marked accord-

ingly on its outside middle surface.

To attach a comb, hold it with

teeth showing, and slide it onto

and along the clipper blade, until

the front of the comb firmly

rests against the clipper blade.

To remove the comb, simply pull

the comb upward and away from

the clipper blade.

For even cutting, allow the comb

attachment / cutter to cut

through the hair. Do not force it

through. Also remember to comb

the hair frequently to remove

trimmed hair and to check for

uneven strands.

STEP 1 - NAPE OF THE NECK

Attach comb attach-

ment 3mm or 6mm.

Hold the clipper cutting

edge pointed up and

begin the haircut, start-

ing at the centre of the

head at the base of the

neck (see diagram 1).

Hold the clipper com-

fortably in your hand

and hold lightly against

the head with the comb

teeth pointing upward.

Gradually and slowly lift

the clipper, working

upwards and outwards

through the hair, trim-

ming just a little at a

time.

As you cut, gradually

lift the hair clipper head

towards you. Continue

to cut the back area

from the bottom of the

neck upwards to the top

of the ears.

STEP 2 - BACK OFTHE HEAD

Change to the next longest comb attach-

ment 9mm or 12mm and cut the back of

the head (see diagram 2).

STEP 3 - SIDE OF THE HEAD

Change to one of two shorter combs

Advertising