Lb" kb, Иг“г^ ^"-3, Wamtng – Инструкция по эксплуатации Beko M 5604 CTX RU
Страница 37
Внимание! Текст в этом документе был распознан автоматически. Для просмотра оригинальной страницы Вы можете воспользоваться режимом "Оригинал".
Pcirf >2* important installation and proparation of your oven
••
Before your appliance is connected to the
mains electricity supply, check to
ensure
that
the voltage and the
frequency
s/iown
in the
data plate corresponds with your power supply.
The data plate is situated back cover of the
oven, or
if
is
sifuafed
in the front of the storage
compartment and can be seen by
openir^
the
sforqge
compartmerit cover or pdling the
drawer.
Wamtng!
This appliance musf be earthed
Our company shall not held responsible for any
damage
caused by the utilisation of the
oven
without ground socket.
Before applying to Authorized service, have
the electrical wiring of your home ready for
conrtection.
if the
appiidnces
is
connecfed
by a plug, that
the plug
IS
eosiVy
accessible after
insfai/afion
fbuf
not above the hob)
•’•'This product must only be
insfa//ed
by a
qualified electrician eg. local electricity
company
fo
a suitable double pole control unit with a
minimum contact clearance of 3 mm in all poles
which should be adjacerrt to (but rюt
above)
the cooker in accordance with lEE regulation.
Failure to observe this instruction moy result in
operatiofKil problems and invalidation of the
producf
worronfy.
If the appliance is connected
by a plug, that the plug is easily accessible
after ir\stallation (but
nof
above the hob).
JhecaldelenglhshoMbe2mtmaxforlsohlion
safety.
in models wifb "small type- fermina/ block"
In mix models a cable supplied with a plug with
your oven (H05
V
V-F 3G 1.5 mm2)
•■ // o
cable without a plug is provided
fogefber
with your oven (H05 V V-F 3G 2,5 mm2 )
Fake
core fo
connect as below:
Brown cable = L (Live)
Blue cable = N (Neutral)
Green/Yellow cable = E (Earth )
If your oven is supplied without supply cord use
schema^ to choose supply cord and use schema-
11 for installation of cord.
The cable length should be max 2m long for
isolation
sofefy.
•■ Open fbe
terminal block cover.
i^Connect the supply cable according to wiring diagram on the rear .
cover.
Fix the supply cable to main body with integrated screw via cable
tightener.
Assembly the terminal block cover to its place.
Your
oven
is suitable for single and three phase connection.
^The mains cable must pass through the cable clamp.
•■ rfie mains
cable should be
roufed
away from the appliance and ..
particular
venfiVofibn s/ofs,
the vent outlet and should not be
ofasfrucfed when
pushed in to oosifibn befween fbe appliance and the wall and/or cabinet.
■
4®
засигзй'ддоУАС
lb" Kb
3gci'j^cw4i&v
Иг“г^
^"-3
2TJAC ЭВО/'IOaMISV
Schema
II
Connection Type
Monophase
Three phase
with Neutral
Two
pbose
with Neutral
Voltage
220/230/
240 V
380/400/
415V
380/400/
415 V
Supply cord type
(max 2m long)
3x2,5 mm2
H05 V V-F
5x2,5 mm2
H05 V V-F
4x2,5 mm2
H05
V/
V-F
о
-JZ
to