WORX Tools WU376.2 - Инструкция (Страница 12)

Cordless Hammer Drill ENG
pack to the highest capacity possible (the red
light stays ON). If the green light (10) flashes
for more than 30mins, the red light (a) will be-
gin to flash slowly indicating the battery pack
is dead.
NOTE: Repaired battery packs are still usable
but should not be expected to perform as much
work as new battery packs.
IMPORTANT CHARGING NOTES:
1.For a new battery or a battery that has been in
storage for sometime, please recharge the bat-
tery before use. If you want to store the battery
for a long time, please fully charge the battery
pack to ensure maximum battery life.
2.Longer life and better performance can be
obtained if the battery pack is charged when
the air temperature is between 65
0 F and 75 0 F
(18 0 -24 0 C). Do not charge the battery pack in air
temperatures below + 40 0 F (+4.5 0 C), or above
105 0 F (40.5 0 C). This is important as it can pre-
vent serious damage to the battery pack.
3.Never freeze your charger or immerse char-
ger in water or any other liquid.
4. When the battery pack fails to produce suf-
ficient power on jobs that were previously
done easily, please recharge you battery, do not
continue to use under this condition. You may
charge a partially used pack whenever you de-
sire with no adverse affect on the battery pack.
5.When charging it is normal that the charger
and battery pack may become warm to touch.
6.If the battery pack does not charge properly:
a.Check current at power outlet by plugging in
another appliance.
b.Plug and unplug to check whether the charger
is ok
c.Check whether the battery has been dam-
aged
d.Move the charger and battery pack to a loca-
tion where the surrounding air temperature is
approximately 65
0 F - 75 0 F (18 0 -24 0 C).
e.If the charging problem persists, take the tool,
battery pack and charger to an authorized ser-
vice center.
f.Under certain conditions, when the charger is
plugged into the power supply, the exposed charg-
ing contacts inside the charger can be shorted by
foreign material. Foreign materials of a conductive
nature such as metallic particles should be kept
away from charger cavities. Always unplug the
charger from the power supply when there is no
battery pack in the charger or before attempting to
clean.
4. TO REMOVE OR INSTALL BATTERY
PACK
Locate latches on side of battery pack and
depress both sides to release battery pack from
your drill. Remove battery pack from your drill
(See B). After recharge insert the battery pack
into drill’s battery port. A simple push and slight
pressure will be sufficient.
5. ON/OFF SWITCH WITH BRAKE
FUNCTION
Depress to start and release to stop your drill
(See C). The on/off switch is fitted with a brake
function which stops your chuck immediately
when you quickly release the switch.
6. SWITCH LOCK
The switch trigger can be locked in the OFF
position. This helps to reduce the possibility of
accidental starting when not in use. To lock the
switch trigger, place the direction of rotation
selector (2) in the center position (See C).
7. REVERSIBLE
The direction selector (2) located above the
switch trigger controls the direction of rotation.
With the drill held in normal operating position,
the direction of rotation selector should be
positioned to the right of the switch for drilling.
The rotation direction is reversed when the
selector is positioned to the left. When the
selector is in the center position, the switch
trigger is locked (See C).
Warming: Never change the
direction of rotation when the chuck
is rotating, wait until it has stopped !
8. VARIABLE SPEED
This tool has a variable speed switch that
delivers higher speed and torque with increased
trigger pressure. Speed is controlled by the
amount of switch trigger depression.
Warning: Do not operate for long
periods at low speed because excess
heat will be produced internally.
13 12
UKR-WU376 WU376.1 WU376¡ª060726.indd 12 2006-7-26 14:05:43