Vitek VT-3461 - Инструкция (Страница 5)

• Держите магнитолу вдали от источников магнитных полей (телевизор, акустические
системы, намагниченные объекты).
• Периодически протирайте корпус мягкой тканью с применением мыльного
раствора. После этого вытрите корпус сухой тканью.
• Не используйте химикаты и химически обработанные очищающие ткани.
• Не беритесь за шнур влажными руками.
СПЕЦИФИКАЦИЯ
Питание
AC 230 В ~ 50 Гц;
DC12 В (C) x 8;
Частотные диапазоны FM1 64 108 МГц;
АM 540 1600 КГц;
Выходная мощность 1.2 Вт х 2 (RMS)
200 Вт (Р.М.Р.О.)
Сопротивление динамиков 8 Ом
Сопротивление наушников 32 Ом
СРОК СЛУЖБЫ МАГНИТОЛЫ НЕ МЕНЕЕ 3 Х ЛЕТ
16
STOP/EJECT button (21)
Press the STOP/EJECT button (21) to cancel a selection, i.e., press this button during cassette play to
stop the tape. In stop mode, press the button to eject the cassette.
PAUSE button (19)
The PAUSE button (19) can be used to interrupt a Recording or Playback temporarily and is useful for
editing the content of the recorded tracks. Press the button once to pause the recording, press the but
ton again to continue the recording.
Note: In Pause mode, the Cassette motor is still energized, therefore the feature should not be used for
long periods of time.
AUTOMATIC STOP
The Cassette mechanism has a built in automatic stop. During Playing/Recording, the unit will automat
ically stop when the end of the tape is detected.
TO PLAY A CASSETTE TAPE
1. Open the cassette door by pressing the cassette STOP/EJECT button (21).
2. Insert a cassette with the exposed tape facing upwards and the full reel on the right (unit plays from
right to left) into the guides on the inside of the cassette door.
3. Close the cassette door.
4. Set the FUNCTION switch (16) to the TAPE position.
5. Press the cassette PLAY button (24) to start the tape playing.
6. Adjust the VOLUME CONTROL (18) to a comfortable listening level.
7. To stop the tape playing, press the STOP/EJECT button (21). Press the button again to open the cas
sette door and eject the tape.
Note: During play, when the end of the tape is reached the PLAY button (24) will pop up and play will stop.
To play the other side of the tape, remove the cassette, turn the cassette over so that the full reel is on the
left, insert the cassette and press the PLAY button (24).
CARE OF CASSETTE TAPES
TO HELP AVOID TANGLES
Loose tape may jam or get tangled in the cassette recorder. With a hexagonal pencil or a similar tool, gen
tly turn the pencil to tighten the tape. If the spool feels tight when taking up slack tape as described
above, this may be due to ridges on the spool of tape. Tight spools can lead to uneven playback speed
or tape tangling. In most cases the ridges can be removed by fast winding the cassette from one end to
the other and back again. Avoid the use of C120 tapes with this unit.
PROTECTING RECORDINGS FROM BEING ERASED.
To prevent recordings from being erased accidentally, break out the tab(s) with a screwdriver. When the
edge with the exposed tape is facing away from you, the tab that protects the side that is uppermost is on
your right. To record on a protected cassette, seal the open slots with adhesive tape.
MAINTENANCE
If the sound becomes muffled or in any case after every 15 hours of operation, clean the pinch roller, cap
stan, erase head and record / play head. Open the cassette door and use a cotton bud moistened with
special tape head cleaning fluid.
CAUTION
Never touch any of the parts described above with a metal object. Do not insert a cassette until the
cleaned parts are completely dry.
AUTOMATIC LEVEL CONTROL (ALC)
This set has the latest Automatic Level control circuitry, therefore, it is not necessary to adjust the Volume
Control when recording. This circuit automatically records at the correct level and prevents over loading.
5
ENGLISH РУССКИЙ
VT-3461.qxd 11.03.03 17:14 Page 10