Инструкция по эксплуатации ASSISTANT AH-1992
Страница 2
– 9 –
– 10 –
– 11 –
– 12 –
– 13 –
– 15 –
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
– 14 –
ENGLISH
ENGLISH
– 16 –
ENGLISH
ENGLISH
DAILY ALARM ON/OFF
Press the key [ALARM] to set the daily alarm on or off.
If no symbol is shown, the alarm function is deactivated.
INFORMATION:
• The clock automatically changes from set-up mode to time
mode if no keys are pressed for 8 seconds.
• The alarm sounds for 2 minutes if no key is pressed to stop
it. If the alarm is not stopped it will repeat after 24 hours.
SNOOZE FUNCTION
To activate the snooze function, follow the steps below
• Press the key [SNOOZE/LIGHT], while the alarm sounds,
to activate the snooze function.
• If the snooze function is activated, the symbol “zZ” is shown
in the display.
• The alarm repeat after 5 minutes.
• The snooze function can be stopped by pressing any key.
TEMPERATURE ALERT SET-UP
• Press and hold the key [ALERT] for 3 seconds until the
temperature alert symbol is flashing.
• Press [CHANNEL] to select the channel (CH1, CH2, CH3)
if more than one transmitter is within reach.
• The symbol for the upper limit of the temperature alert is
flashing.
• Use [▲] and [▼] to select the maximum temperature.
• Press [ALERT] to confirm.
• The symbol for the lower limit of the temperature alert is
flashing. Use [▲] and [▼] to select the minimum tem-
perature.
• Press [ALERT] to confirm and complete the temperature
alert set-up.
TEMPERATURE ALERT ON/OFF
Press the key [ALERT] to set the temperature alert for all
transmitter channels on or off.
• Alert on: Temperature alert symbol shown in display
• Alert off: Temperature alert symbol goes out.
INFORMATION
• A temperature alert can be set-up for each channel.
• The set-up process cannot be completed if the maximum
temperature selected is lower than the minimum selected
temperature.
• The minimum temperature selected must at least be 1°C
below the maximum selected temperature.
• The respective channel and the maximum, respectively the
minimum limit symbols are shown when the temperature
alert sounds.
12/24 HOURS MODE
The time display can be in 12 or 24 hours mode. Press the
key [▲] to switch between the modes.
°C/°F TEMPERATURE DISPLAY
The temperature display can be in °C or °F. Press the key
[-] to switch between the modes.
TEMPERATURE TREND DISPLAY
The meteorological station measures the current tem-
perature once batteries are inserted. The temperature trend
display shows a neutral trend (horizontal arrow).
• The subsequent trend of the temperature trend display
is as follows:
• If, after one hour, the temperature is more than 1 °C higher
than the initial value, a positive trend is shown (upward
arrow)
• If, after one hour, the temperature is more than 1 °C lower
than the initial value, a negative trend is shown (downward
arrow)
• If, within one hour, the temperature remains constant, the
upward arrow, respectively the downward arrow changes to
a horizontal arrow. The measured temperature serves now
as a neutral value and basis for future forecasts.
WEATHER FORECAST
This function allows a weather forecast for the next 12 to
24 hours.
Please note that during the first 12 hours after inserting
batteries, the weather forecast will not be accurate. After
a re-start, the weather station needs time to adjust to the
conditions.
The station displays 4 different symbols to forecast the
weather.
Sunny Slightly cloudy Cloudy Rain
REMARKS as the weather is forecasted only by data of
temperature and humidity, no barometer.
• The display will have discrepancy with the actual weather
sometime.
MOON PHASE DISPLAY
The weather station uses saved data to show the moon
phase
A B C D E F G H
A: New moon
B: increasing crescent C: First quarter
D: increasing 3/4 E: Full moon F:
decreasing 3/4
G: Last quarter H: decreasing crescent
LIVING SPACE HUMIDITY
The weather station uses saved data to determine the hu-
midity in the living space and shows the respective symbols.
comfortable dry humid
Warranty period
Гарантийный срок
Date of sale
Дата продажи
Model
Номер модели
Stamp
Печать магазина
BATTERY CONDITION DISPLAY
The weather station displays the battery condition symbol
to show whether the batteries of the weather station or the
transmitter need to be exchanged.
• Weather station battery condition display: within indoor
area of the display
• Transmitter battery condition display: in the outer area of
the display.
ILLUMINATION
Press the key [SNOOZE/LIGHT] to activate the display
illumination for 5 seconds.
WIRELESS CONNECTION
TO THE TRANSMITTER
• Press the key [CHANNEL] to select a channel. You can
read the data of up to 3 transmitters at one weather station.
• Press and hold the key [CHANNEL] for 3 seconds to search
for transmitters. You can exit this process by pressing the
key [CHANNEL].