ZELMER 400 - Инструкция (Страница 36)

40
3 Replace it with a new filter, making sure it is installed
correctly under the fastenings.
4 Install and close the filter cover – the fastenings should
snap hut. If the inlet filter cover is closed correcly, you should
hear a clicking sound when doing it.
ATTENTION! Always replace a damaged inlet filter only
with a brand new one.
SAFBAG dust bag disassembly/assembly
1 The vacuum cleaner is equipped with safety valve located
in chamber of dust container (bag). It opens automatically
in case of total stopping of suction hose or total stopping of
equipment elements connected thereto, as well as in case
of overfill of dust bag. After opening the valve one can hear
characteristic “whirr” sound inside the vacuum cleaner.
2 Switch off the vacuum cleaner by pressing the on/off
button (1).
3 Unplug the appliance.
4 Pull the end of the hose out of the inlet opening of the
vacuum cleaner.
5 Release the front cover fastening (8) and open the
cover.
6 Put the vacuum cleaner in a vertical position (it is easier
to open and put it on its back wheels, while its second half
leans over the front part of the dust container).
7 While holding the bag plate, pull it aside towards the
inside of the dust container, and then pull the bag up.
8 Close the SAFBAG bag cover in order to cover the
opening of filled bag. Throw it out into garbage container.
9 Place the plate in the new bag before the sliders and
slide it in along with the screen right down to the bottom of
the container. Unfold the bag. The direction is shown by an
arrow placed on the bag.
10 Close the cover until you hear the characteristic clicking
sound – be careful not to catch the bag.
ATTENTION! Do not start cleaning without an installed
SAFBAG bag.
ZELMER vacuum cleaners are equipped with SAFBAG dust
bags in the amount indicated in the table. It is recommended
to replace the dust bag if:
a) the safety valve activates,
b) the vacuum cleaner operates poorly,
c) the dust bag is full.
Special accessories
The following special accessories may be purchased in retail
outlets:
Zelmer electrobrush (22)
Only the electrobrush manufactured by ZELMER may be
used with ZELMER vacuum cleaners. Using other brands of
electrobrushes may cause damage to the vacuum cleaner.
F
The electrobrush may be used with all ZELMER vacuum
cleaners equipped with the appropriate electrobrush socket.
While using the electrobrush follow the instruction manual.
The electrobrush is especially helpful in cleaning worn out
carpets. Before vacuuming remove all larger elements from
the floor such as: remains of cloth, paper etc. in order to
prevent blocking of the whirling element of the brush.
Zelmer turbobrush (21)
May be used with all types of ZELMER vacuum cleaners. Is
used for an effective vacuuming of carpets and fitted carpets.
While using the turbobrush follow the instruction manual.
The use of the turbobrush decidedly increases the
effectiveness of removing fibrous dirt such as: animal hair,
hair, threads etc. It is practically useful in households with
pets (cats, dogs), where removing the animal hair from the
carpets and floorings is very onerous.
End of operation cleaning
and maintenance
1 Switch off the vacuum cleaner by pressing the “on/off”
button (1).
2 Unplug the appliance.
3 Wind the cord by pressing the cord rewind button (3).
While doing this hold the cord to make sure it is not tangled
and the plug does not hit the vacuum cleaner housing.
4 Disconnect the suction tube from the suction nozzle or
brush.
5 Disconnect the suction tube from the hose.
6 Pull the end of the hose out of the inlet opening of the
vacuum cleaner.
7 The vacuum cleaner may be stored in a vertical position
– just place the fastening hook of the combination brush
into the fastening of the combination brush. The hose may
be connected to the vacuum cleaner. Yet it is necessary to
make sure it is not bent to hard during storing time.
8 If necessary wipe the housing and the dust bag container
with a damp cloth (it may be soaked with dishwashing liquid)
and dry it or wipe until dry.
Do not use abrasive detergents or solvents.
Examples of problems while operating the
vacuum cleaner
PROBLEM ACTION
A characteristic “fluttering”
of the vacuum cleaner is
heard which indicates the
opening of the safety
valve.
• The dust bag may be full – replace
the dust bag.
• Replace the dust bag even if it is not
full yet. In unfavorable conditions, fine
dust might have clogged the pores on
the surface of the dust bag.
• The suction tube, the hose or the
attachment is blocked – remove the
cause of the clogging.
The dust bag is damaged. Remove the dust bag and the filters.
E