ZELMER 400 - Инструкция (Страница 35)

39
B
Appliance elements
1 ON/OFF button
2 Handle
3 Cord rewind button
4 Combination brush fastening
5 Plug and cord
6 Outlet filter cover
7 Electrobrush socket (type 400.0 EK, 400.0 EP)
8 Front cover fastening
9 Suction power regulation lider
10 Accessory compartment cover
11 Suction hose. The vacuum cleaner is equipped with one
suction hose (A or B)
A Suction hose FLEXI (type 400.0 EK, 400.0 EP)
B Suction hose CBS (type 400.0 EF)
12 Suction pipe. The vacuum cleaner is equipped with one
kind of suction pipe (A or B)
A Telescopic suction tube (type 400.0 EK, 400.0 EP)
B Segmented suction tubes (type 400.0 EF)
13 SAFBAG dust bag (2 pieces)
14 Outlet filter “Elektret” (installed in the vacuum cleaner)
15 Inlet filter (installed in the vacuum cleaner)
16 Crevice nozzle
17 Small brush
18 Small nozzle
19 Parquet brush “BNB” (type 400.0 EP)
Is used to clean and polish hard, scratch sensitive surfaces
such as wooden floors, floor panels, parquet, marble, tiles,
etc.
Delicate and soft natural bristles ensure maximum vacuum
effectiveness and protects against scratching the cleaned
surface.
20 Combination brush. The vacuum cleaner is equipped
with only one type of combination brush (A or B)
A Universal combination brush
B Switchable combination brush
21 Turbobrush (additional equipment – may be bought in
retail centers)
22 Electrobrush (additional equipment – may be bought in
retail centers)
Preparing the vacuum cleaner
for operation
1 Pull the end of the suction hose into the opening and
press lightly.
2 Attach the other end of the suction hose (the handgrip) to
the suction tube.
3 Join both segments of the suction tube together.
4 In case of the telescopic suction tube adjust the
necessary tube length by moving the slider according to the
slide in/slide out direction arrow.
5 Assemble the appropriate nozzle or brush to the other
end of the suction tube.
6 In case of the switchable combination brush adjustable
for clearing hard surfaces – wooden, plastic or ceramic
tiles floors, slide the brush out by pushing the switch on the
combination brush according to the figure .
7 The vacuum cleaner is equipped with an accessory
compartment. In order to open the compartment pull the
accessory compartment cover towards yourself.
8 Grab the plug (5) and pull the cord out of the vacuum
cleaner.
ATTENTION! While puling out the cord pay attention
to the yellow stripe which signals the end of the
cord. Further attempts (pulling on cord) may result in
damaging the cord.
9
Plug in the appliance.
Before operation make sure that the SAFBAG bag is installed
in the vacuum cleaner chamber and that inlet filter and the
outlet filter is installed in the appliance.
10 Switch on the vacuum cleaner by pressing the “on/off”
button (1).
11 The vacuum cleaner is equipped with electronic power
regulator allowing a stepless regulation of vacuum cleaner
power. The power regulation is performed with a slider.
12 Moving the slider according to its mark ( or ) will
increase or reduce the suction power.
Filter disassembly
Before changing the filters make sure that the vacuum
cleaner is switched off and unplugged from the mains
supply.
INLET FILTER
1 Release the catch of front cover (8) and open it.
2 Remove the inlet filter (15) out of the housing.
3 Replace it with a new one, paying attention that the outer
edge of the filter is placed inside the safety rib.
4 Close the front cover of the vacuum cleaner.
ATTENTION! The damaged inlet filter should be replaced
with a new, genuine manufactured product only.
ATTENTION! It is advised to replace the inlet filter
every 4 replacements of the SAFBAG dustbug, or even
more often, if necessary.
“ELEKTRET” INNER FILTER
1 Push the fastening in the inlet filter cover and remove the
cover from the vacuum cleaner.
2 Pull the used filter out of the fastenings.
A
C
D