Vitek VT-3505 - Инструкция (Страница 4)

ENGLISH
4
• Close the battery compartment lid.
Attention! Battery leakage can lead to injuries or
damages of the unit. In order to avoid damaging of
the unit, follow the following instructions:
- insert the battery properly;
- remove the battery if you are not planning to use
the unit for a long time;
- do not recharge, do not dismantle, and do not
subject the battery to high temperatures;
- replace the battery in time.
Note:
The unit is intended for operation from the mains,
battery operation is a reserve option.
The battery helps to store the settings while switch-
ing off, or absence of power.
Remove the battery if you are not planning to use
the unit for a long time.
Connecting the unit
Before connecting the unit, make sure that the elec-
tricity supply in your home sockets corresponds to
the voltage specified on the housing of the unit.
Insert the plug into the socket.
Listening to the radio
1. Press the button to start listening to the ra-
dio.
2. Select the desired band (FM or AM), by pressing
the BAND button. The corresponding signal will
appear on the display.
3. Rotate the TUNING knob to tune to the desired
radio station.
4. Use the VOLUME control to set the required vol-
ume level.
5. After you finish listening to the radio, press the
button once again.
Note: For better receipt of FM stations we recom-
mend full unwinding of the FM-antenna cord and its
optimal location. For better receipt of AM stations,
try several options of the unit location.
Setting the current time and date
In the current time mode press and hold the MODE
button for more than 2 seconds to enter the Setting
current time and date mode.
The year digits will start flashing on the display. Use
the <</>> buttons to set the year.
Press the MODE button. The month digits will start
flashing on the display. Use the <</>> buttons to
set the month.
Press the MODE button. The day digits will start
flashing on the display. Use the <</>> buttons to
set the day.
Press the MODE button. Time format symbols will
start flashing on the display: 24-hour format or 12-
hour format. Use the <</>> buttons to select the
time format.
Press the MODE button. The hour digits will start
flashing on the display. Use the <</>> buttons to
set the hour.
Press the MODE button. The minute digits will start
flashing on the display. Use the <</>> buttons to
set the minute.
Note: If during 2 seconds the <</>> buttons are
not pressed, the unit will switch to the current time
mode.
Displaying date
In the current time mode, press the << button to
display the date; the >> button to display the year.
In 5 seconds the unit will switch to the current time
mode.
Daylight saving time
Press and hold the >> button for more than 3 sec-
ond to go on daylight saving time and back.
Setting temperature units (С/F)
Press and hold the << button for more than 3 sec-
ond to select between temperature units (С/F)
Setting the alarm actuation time (AL.1 and
AL.2)
In the current time mode press and hold the AL.SET
button for more than 2 seconds to enter the alarm
actuation time setting mode.
Hour digits will start flashing on the display. Use the
<</>> buttons to set the hour.
Press the AL.SET button. Minute digits will start
flashing on the display. Use the <</>> buttons to
set the hour.
Press the AL.SET button. Alarm actuation symbols
will start flashing on the display. Use the <</>> but-
tons to select the necessary mode:
1 – 5: alarm actuation from Monday till Friday;
1 -7: alarm actuation from Monday till Sunday;
6 - 7: alarm actuation in Saturday and Sunday;
1 - 1: alarm actuation once a week.
In the same manner the actuation time and date of
Alarm 2 can be set.
Note: If during 2 seconds the <</>> buttons are
not pressed, the unit will switch to the current time
mode.
Alarms signal type selection, alarm on/off
Consequently press AL.1/ AL.2 to select radio
3505IM.indd 4 3505IM.indd 4 21.05.2010 16:22:52 21.05.2010 16:22:52