Инструкция по эксплуатации ZELMER 491
Страница 75
79
3
Unlock and remove the blender drive (after the appliance
stops completely).
4
Remove the pusher from the lid chute (in order to open
the lid it is necessary at first to remove/lift the pusher out of
the chute).
5
Unlock and open the lid.
6
Remove the permanent guard (in case of dicer together
with grid).
7
Remove the disc.
8
Unlock the container.
9
Remove the container from the base.
10
Empty the container removing the products.
Operating instructions
Chipping and puree disc
During operation with chipping and puree disc it is
●
recommended to apply the blender drive speed 15 or
TURBO.
Insert the processed product into the feed chute, hold the
●
pusher (do not press), switch on the blender drive. When
the appliance is in operation press the pusher with a bit
of power.
When the container is filled up to MAX level, stop the
●
operation, empty it and collect the scrap accumulated on
the disc.
Slicing disc
During operation with slicing disc it is recommended to
●
apply the blender drive speed 15 or TURBO.
It is recommended to insert the products onto the feed
●
chute in vertical position so that they fill in complete
space of the chute.
Insert the processed product into the feed chute, hold the
●
pusher (do not press), switch on the blender drive. When
the appliance is in operation press the pusher with a bit
of power.
When the container is filled up to MAX level, stop the
●
operation, empty it and collect the scrap accumulated on
the disc.
OPERATION WITH ICE CRUSHER
The appliance characteristics
Zelmer hand blender is equipped with ice crusher which is
used for crushing ice and i.e. frozen fruits.
ATTENTION! You can use the crusher only with the
container and lid of mini food processor!
Application of the accessories
Double-sided disc – is used for crushing, grinding ice and
frozen products. The disc is round, the blades are double-
sided. One side, which we recognize by the applied plastic
fifteen- pointed star, fig. 14a is used for first level grinding
„I” (smaller particles of grinded product), the other side is
used for second level grinding „II” (bigger particles of grinded
product) and it is marked with seven-pointed star fig 14b.
Spindle – is used for fixing the disc.
Preparation of the ice-crusher
ATTENTION! Before assembling and disassembling
blender motor drive On the ice crusher, make sure if
the supply cord plug is disconnected from the mains
supply outlet.
Wash the parts in contact with processed product before
first usage.
Operate the blender so, that the closed/open markings
located on the appliance are well visible.
Operation with ice crusher (Fig. I)
1
Place the container of the mini food processor on firm,
flat and dry surface.
2
Place the disc for ice on the spindle (double – sided
disc), so that the blades provided for operation are on the
top.
3
Place the disc with the spindle inside the mini food
processor container so that the pivot protruding from the
container is inserted into the spindle orifice.
4
Insert the ice crusher container on the fasteners of the
mini food processor. Then lock the crusher container, turning
it until you can feel it is blocked.
5
Place the processed products inside the container not
exceeding MAX level.
When you fill up the crusher container (13) with
appropriate amount of processed product (do not
exceed MAX level) center the spindle (15) (put in the
middle) to enable its proper coupling with the mini food
processor lid (9).
6
Insert the mini food processor lid including the gearbox
into the fasteners of the ice crusher container. Then lock the
lid turning it until you feel it is blocked.
7
Insert the blender drive on such assembled ice
crusher
.
8
Lock the blender drive .
9
Connect the plug into the mains supply outlet.
10
Start-up the appliance pressing TURBO switch of the
blender motor drive.
After operation, switch off the appliance and unplug it
●
from the socket.
Disassembling the ice crusher, proceed reverse to its
●
assembling.
ATTENTION! The ice crusher blades are very sharp.
Be very careful during assembling, disassembling or
during cleaning.
ATTENTION! Never exceed the maximum level of the
ice crusher input.