Инструкция по эксплуатации ZELMER 491
Страница 74
78
Approximate time for processing of selected
products for the recommended gear
Product
Recommended
gear
Processing
time
TURBO
20-30 s
TURBO
25-30 s
1/4
8-10
15 s
15
+TURBO
40 s + 5 s
(
×30
)
15
10 s
15
+TURBO
15 s + 5 s
TURBO
30 s
You can shorten the processing time as you wish, then you
obtain other granulation of grinded products.
OPERATION WITH FOOD PROCESSOR AND
DICER
The appliance characteristics
ZELMER hand blender equipped with food processor including
dicer is used for chopping, pureeing fruit and vegetables, as
well as dicing boiled vegetables, eggs and soft fruit.
The application of the food processor accessories
Double – sided slicing disc – is used to slice fruit and
vegetable (raw, boiled) into thin or thick slices. The slicing
disc is round, with double -sided blades (one side for thin
slices, the other side for thick slices).
Double – sided chipping and puree disc – is used for
chipping and pureeing fruit and vegetables. Chipping and
puree disc is round, with double -sided blades (one side for
chipping i.e. carrots, celery boiled beetroots, the other side
for pureeing – i.e. for potato pancakes, beetroot salad).
Disc driver – is used for assembling discs (for slicing,
chipping and pureeing).
Pusher – is used for pushing product grinded with all discs
and closing the lid feed chute.
ATTENTION! We use the permanent guard for all discs
of the food processor and dicer.
ATTENTION! The slicing and pureeing process cannot
last longer than 2 min. After this time, wait until the
motor cools down before next usage of the blender.
Preparation of the food processor and dicer for
operation
ATTENTION! Before assembling on and removing the
blender drive out of the food processor, make sure
that the plug of the supplying cord is disconnected
from the mains supply outlet.
Wash the parts in contact with processed product before
first usage.
Operate the blender so, that the closed/open markings
located on the appliance are well visible.
Operation with food processor and dicer (Fig. E)
1
Place the base of the food processor on firm, flat and
dry surface. Insert the food processor container into the base
fasteners.
2
Lock the container.
Operation with food processor (slicing disc,
chipping and puree disc) (Fig. F)
1
Place the selected disc on the disc driver (double-sided
discs) so that the blades provided for operation are on the top.
2
Insert the accessory inside the container, so that it is
connected with the drive shaft.
3
Insert the permanent guard. The guard can be assembled
inside the food processor container in one position only, so
that the protrusion of the permanent guard is locked inside
the handle of the food processor container.
4
Insert the lid of the food processor into the fasteners of
the container (take care that the lid is fastened with all the
fasteners).
5
Lock the lid.
6
Insert the blender drive (assembling of the drive is
possible only when the container lid is closed). Then lock it.
7
Set the desired gear using the speed control knob.
8
Insert processed products into the lid chute.
9
Hold the pusher to the chute, so that it does not press
the product before start – up of the appliance (push the next
portions of products when the blender drive is in operation /
the disc is rotating).
10
Connect the plug into the mains supply outlet. Then start –
up the appliance pressing the switch (2) of the blender drive.
After operation of the food processor and dicer
(Fig. H)
1
Release the button (2) (or TURBO in case of using this
gear).
2
Remove the plug of the supply cord from the mains
supply outlet.
200 g
(500 ml)
20 g
(500 ml)
300 g
300 g
(500 ml)
250 g
(500 ml)
200 g
(500 ml)
1 cm
1 cm
250-300 g
(400-500 ml)