ZELMER 01z011 - Инструкция (Страница 25)


Dear Clients!
Please read these instructions carefully. Pay your special attention to important safety instructions. Keep this User’s Guide for future reference.
The manufacturer/importer does not accept any liability for any damages resulting from unintended use or inappropriate handling. The manu-
facturer/importer reserves his rights for modifying the product any time in order to adjust it to law regulations, norms, directives, or due to
construction, trade aesthetic or other reasons, without notifying it in advance.
IMPORTANT SAFETY INSTRUCTIONS
The vacuum cleaner is intended for domestic usage only.
Connect the vacuum cleaner to 220-240V mains supply, equipped with fuse 16A.
Do not unplug by pulling on cord.
Do not use the appliance, when the casing or the cord is visibly damaged.
If the power cord is damaged, it shall be exchanged by special service desk staff, due to avoid hazard.
The appliance should be repaired by trained staff only. Improper repair can result in serious hazard for a user. In case of defects we recom-
mend you to contact qualified ZELMER service desk.
Do not run the vacuum cleaner or brushes over the cord; it can result in cord insulation damage.
Unplug before cleaning and maintenance.
Do not use without the bag, filters or in case damage of the bag.
Do not use this vacuum cleaner to clean people or animals; be especially careful to keep the nozzles away from ears and eyes.
Do not pick up: matches, cigarettes, hot ash.
Avoid picking up sharp objects. Do not vacuum wet objects; do not pick up water or other liquids.
Control sucking hose, pipes and nozzles – remove the rubbish accumulated inside.
Do not pick up fine dust such as: flour, cement, gypsum, toners for printers and copy machines, etc.
The vacuum cleaner is intended for indoor usage and dry surfaces cleaning only.
Dry the wet cleaned carpets before vacuuming.
It is forbidden to cover ventilation outlets during operation.
Heated air without any outlet can cause motor overheating which can result in motor damage; it can also cause plastic parts deformation.
People (including children), who because of their physical, sensory or intellectual capabilities or their inexperience or lack of knowledge are unable to
use the appliance safely, should not use this appliance unless under supervision or instructed to do so by a responsible person. Do not leave the ap-
pliance unattended during operation.
Do not leave the appliance unattended during operation.Do not allow children into any contact with the appliance.
Children should be supervised to ensure that do not play with the appliance.
STANDARD REQUIREMENTS AND TECHNICAL DATA
The vacuum cleaner is II class appliance and it meets the requirements of effec-
tive standards.
The appliance meets the requirements of the following directives:
Low Voltage Device (LVD) – 2006/95/EC,
Electro- Magnetic Compatibility (EMC) – 2004/108/EC.
The product is marked with CE symbol on the name plate.
Voltage – 220-240V/50Hz. Power – 1500W.
You can find the vacuum cleaner technical data on the name plate.
PREPARATION FOR OPERATION
Insert the hose into the vacuum cleaner inlet. Press two side buttons at the
hose ending.
Connect later ending (handle) with telescope sucking pipe.
Adjust the telescope sucking pipe length in desired working position (depend-
ing on user’s height) move the knob in direction indicated by the arrows.
Assemble selected accessory to telescope pipe.
Take the power cord out of the vacuum cleaner casing
and connect it into the mains supply outlet.
Pay attention to yellow mark on the cord, when you take it out, the mark show that the end of the cord is near.
Red mark indicated the end of the supplying cord.
Start up the vacuum cleaner pressing ON/OFF button at the vacuum cleaner and adjust proper suction power with
electronic regulation knob or with the knob on hose handle.
SUCTION POWER ADJUSTMENT
The vacuum cleaner is equipped with electronic power adjustment, which enables fluent power regulation. Moving the
knob according to mars on the appliance shall cause increase or reduction of suction power.
The vacuum cleaner is also equipped with mechanical suction adjustment on hose handle. To reduce or increase suction
power it is enough to move the knob in direction indicated by the arrow.
VACUUMING
Select adequate brush or nozzle:
Soft surface – carpets and fitted carpets, etc.
We recommend you to use brush-nozzle with sucking pipe and switch it for carpet cleaning function:
hidden brush - according to the photo beside ).
Hard surface – wooden, floor, laminates, ceramic tiles, etc.
We recommend you to use brush-nozzle with brush out - according to the
figure beside ).
Gaps, corners, cavities, etc.
Gap nozzle is used for vacuuming: gaps, corners, spaces and other recesses with difficult access.
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
GB
Front lid
Full dust compartment
(bag) indicator
Suction power
adjustment knob
Carrying handle
Cord rewind button
Supply cord
ON/OFF button Outlet filter protection
Red mark
Yellow mark