Инструкция по эксплуатации Carrier 42UQV

Страница 4

Advertising
background image

Set your preferred operation for future use. The setting will be memorized by the
unit for future operation (except airflow direction).
1. Select your preferred operation.

2.

Press and hold

for 3 seconds to memorize the setting. The

P

mark displays.

3.

Press

: Operate the preset operation.

To automatically restart the air conditioner after the power failure (Power of the
unit must be on.)

Setting

1.

Press and hold the RESET button on the indoor unit for 3 seconds to set
the operation. (3 beep sound and OPERATION lamp blink 5 time/sec for 5
seconds)

2.

Press and hold the RESET button on the indoor unit for 3 seconds to cancel
the operation. (3 beep sound but OPERATION lamp does not blink)

• In case of ON timer or OFF timer are set, AUTO RESTART

OPERATION does not activate.

For ECO sleep automatically control air flow and automatically turn OFF.

Press

: Select 1, 3, 5 or 9 hrs for OFF timer operation.

Note: The cooling operation, the set temperature will increase automatically

1 degree/hour for 2 hours (maximum 2 degrees increase). For heating
operation the set temperature will decrease.

To operate at super low fan speed for quiet operation (except in DRY mode)

Press

: Start and stop the operation.

Note: Under certain conditions, QUIET operation may not provide adequate

cooling due to low sound features.

To separate using of remote control for each indoor unit in case of 2 air
conditioners are installed nearly.

Remote Control B Setup.

1. Press RESET button on the indoor unit to turn the air conditioner ON.
2. Point the remote control at the indoor unit.
3. Push and hold

button on the Remote Control by the tip of the pencil.

“00” will be shown on the display.

4. Press

during pushing

. “B” will show on the display and “00”

will disappear and the air conditioner will turn OFF. The Remote Control B
is memorized.

Note: 1. Repeat above step to reset Remote Control to be A.

2. Remote Control A has not “A” display.

3. Default setting of Remote Control from factory is A.

The unit does not operate.

Cooling is abnormally low.

• The power main switch is turned off.
• The circuit breaker is activated to cut

off the power supply.

• Stoppage of electric current
• ON timer is set.

• The filters are blocked with dust.
• The temperature has been set

improperly.

• The windows or doors are opened.
• The air inlet or outlet of the outdoor

unit is blocked.

• The fan speed is too low.
• The operation mode is FAN or DRY.

2

1

PRESET OPERATION

12

ECO SLEEP OPERATION

15

QUIET OPERATION

14

AUTO RESTART OPERATION

13

Firstly, turn off the circuit breaker.

Filter Reset
FILTER lamp lights on; the filter must be cleaned.
To turn off the lamp, push the RESET button on the indoor unit or the FILTER
button on the remote control.

Indoor Unit and Remote Control

• Clean the indoor unit and the remote control with a wet cloth when needed.
• No benzine, thinner, polishing powder or chemically-treated duster.

MAINTENANCE

16

TROUBLESHOOTING (CHECK POINT)

18

REMOTE CONTROL A-B SELECTION

19

1.

Three-minute protection feature: To prevent the unit from being activated
for 3 minutes when suddenly restarted or switched to ON.

2.

Preheating operation: Warm up the unit for 5 minutes before blowing warm
air.

3.

Warm air control: When the room temperature reaches the set
temperature, the fan speed is automatically reduced and the outdoor unit
will stop.

4.

Automatic defrosting: Fans will stop during defrost operation.

5.

Heating capacity: Heat is absorbed from outdoor and released into
the room. When the outdoor temperature is too low, use another
recommended heating apparatus in combination with the air conditioner.

6.

Consideration for accumulated snow: Select the position for outdoor unit
where it will not be subjected to snow drifts, accumulation of leaves or
other seasonal debris.

7.

Some minor cracking sound may occur when unit operating. This is
normal because the cracking sound may be caused by expansion/
contraction of plastic.

Note: Item 2 to 6 for Heating model

Air conditioner operating conditions

Temp.

Operation

Outdoor Temperature

Room

Temperature

42UQV035M,

050M, 060M Series

42UQV025M

Series

Heating

–15°C ~ 24°C

–10°C ~ 24°C

Less than 28°C

Cooling

–10°C ~ 46°C

15°C ~ 43°C

21°C ~ 32°C

Dry

–10°C ~ 46°C

15°C ~ 43°C

17°C ~ 32°C

OPERATION AND PERFORMANCE

17

Carrier1110655103(01_EN).indd 4

Carrier1110655103(01_EN).indd 4

2/6/13 3:19 PM

2/6/13 3:19 PM

Advertising