Vitek VT-3950 - Инструкция (Страница 6)

ENGLISH
6
recorded in MP format, but there are cases,
when the disc is not played back due to settings
of the software that was used while recording
the disc.
. Select the disc playback mode, by setting
the operating mode switch to CD/MP
position.
2. Open the disc slot by pressing the
OPEN/CLOSE button. Put the disc into
compartment and close the Set the disc and
close the Set the disc and close the slot lid.
Make sure that the disc is inserted properly
– with its label down.
. To playback press the ►║ button. To pause
the playback, press this button once again.
. To stop the playback, press the ■ button.
5. In the playback mode you can move to the
next or to the previous track, by pressing the

or  buttons correspondingly.
Note: CD/MP playback will stop while opening
the disc slot, while switching to the radio mode.
Selecting a track, moving to the next/previ-
ous track
While playback or stop the playback you can se-
lect the desired track using the  or  buttons.
To move to the next track press the  button
once.
To move to the previous track press in the play-
back mode the  button.
Fast rewind/fast forward
Press and hold the  or  buttons to fast for-
ward or rewind correspondingly, sound will be
reproduced brokenly.
Selecting a folder
To select a folder press and hold the +0/FOL+
or -0/FOL- buttons on the remote control for
more than  seconds, folder numbers will be
successively displayed on the LCD-display:
F0
→F02 etc. When the number of the desired
folder appears on the LCD-display, release the
button.
Different playback modes
Repeat/random playback
Pressing successively the REPEAT/RANDOM
button on the player or on the remote control,
you can select one track repeat, the whole disc
repeat, folder repeat or random playback
Note: In the programmed playback mode, folder
repeat is absent.
Programmed playback
You can program playback of tracks (max. 99) at
the desired order.
. When the playback of the disc is stopped,
press the PROGRAM button once. Track
number while programming “P-” will
appear on the LCD-display.
2. Select the desired track, successively
pressing the  or  buttons. Press the
PROG button to store the selected track.
. Repeat steps  and 2 to program other
tracks.
. To playback the programmed tracks press
the PLAY/PAUSE/USB button.
5. To stop playback of tracks in the
programmed order press the STOP button
once. To cancel programmed playback
press the STOP button once again.
Playback of МР3 files from the external de-
vice (USB/ SD/MMC)
In the disc playback mode press and hold the
PLAY/PAUSE/USB button for more than ,5
seconds, the CD/MP player will switch to the
USB mode. The “- - -“ symbols will appear on
the LCD-display. To switch to the discs playback
mode press and hold this button for more than
,5 seconds once again.
To switch to the SD/MMC mode press and hold
the STOP/SD button for more than ,5 seconds.
The “- - -“ symbols will appear on the LCD-dis-
play. Press the PLAY button to start playback.
While successful reading of the external device,
track playback will start.
Control buttons and actions sequence while
operation with the external device are the same
as those while operation with the disc.
Maximal number of folders is 500; maximal
number of tracks is 999.
Note: This unit does not support playback from
all HDD and some MP players, as well as play-
back of МР files with byte rate more than 256
Kbit/sec from external devices.
Note: In case if you switched the CD/MP
player from the USB mode to the SD/MMC
mode and the external device is not connected
or cannot be read, “no” will appear on the LCD-
display.
3950IM.indd 6 19.05.2008 14:58:32