Инструкция по эксплуатации Saturn ST-CC0218
Страница 3
4
4. The iron should always be switched
off before connecting or disconnecting
from the power supply. Do not pull on
the cord to disconnect the plug from the
wall socket.
5. Do not use the iron when it is
damaged in any way. Do not operate
the iron with a damaged cord or plug.
Do not replace the power cord or any
other
parts
by
yourself-contact
Customer Support for Assistance.
6. The
iron
must
not
be
left
unattended while it’s connected to the
supply mains.
7. The iron must be removed from the
socket outlet before the water reservoir
is filled with water (for steam irons
incorporating
means
for
spraying
water).
8. The iron must be used and rested
on stable surface.
9. When placing the iron on it’s stand,
ensure that the surface on which the
stand is placed is stable.
10. The iron is not to be used if it has
been dropped, if there are visible signs
of damage or if it’s leaking.
11. This appliance is not intended for
use by persons (including children) with
reduces physical, sensory or mental
capabilities or lack of experience and
knowledge, unless they have been given
supervision or instruction. It is not
advised to use this appliance by children
under 14.
12. Children should be supervised to
ensure that they do not play with the
appliance.
SPRAYING
This function can be used any time and
it
does
not
affect
the
ironing
temperature.
Fill water into the iron.
Aim the nozzle towards the garment.
Press the spray button.
STEAM IRONING
This function can be used only at higher
ironing temperature
• • for moderate steam
• • • or MAX for maximum steam
Fill water into the iron.
Stand the iron upright.
Connect he iron to a suitable mains
supply outlet
Turn the temperature control button
to the “• • ”, or “• • •” "MAX" setting
The pilot light turns on when the
required temperature is reached. The
iron is ready for use.
Turn the steam knob to the required
position, steam starts coming out from
the holes in the sole plate.
Notice:
With
conventional
steam
ironing, water may leak from the sole
plate if too low temperature has been
select.
If
this
happens
turn
the
temperature control to the advised
position. Steam will recommence as
soon as die appropriate temperature has
been reached.
BURST OF STEAM
This function provides an extra amount
of steam to remove stubborn wrinkles.
Fill the iron with water.
Turn the temperature control to the
position 'MAX".
The iron is ready for use.
Press the burst of steam knob once
Steam
will
penetrate
into
the
garment removing the wrinkles.
Wait a few seconds before pressing
the steam control knob wrinkles again
when there are stubborn wrinkles.
Usually all wrinkles can be removed
within three pressings.
DRY IRONING
Connect the iron to a suitable mains
supply outlet.
Ensure that the steam control knob
is in position “0”.
Select
the
setting
on
the
temperature control.
When the pilot light turns off, the
required temperature is reached. The
iron is ready to use.
TO LET THE IRON HEAT UP AGAIN
Pick up the iron or move it slightly.
The red shot-off pilot goes out. If the
temperature of the soleplate drops
below the set ironing temperature, the
temperature pilot goes on.
If the pilot light goes on after you have
move the iron, wait for it to go out
before you start ironing.
If the pilot light does not go on after
you move the iron, the soleplate still
has right temperature and iron is ready
for use.
SELF CLEAN FUNCTION
The Self Clean function can remove any
scale or impurities.
Use the self-clean function once every
two weeks. If the water in your area is
very hard, the self-clean function should
used more frequently.
Make
sure
the
appliance
is
unplugged.
Set the Variable steam control knob
to position "0" (=no steam).
Fill the water tank to the maximum
level.
Select
the
maximum
ironing
temperature.
Put the plug in the wall socket.
5
Unplug
the
iron
when
the
temperature pilot light has gone out.
Hold the iron over the silk, press and
hold die self-clean button and gently
shake the iron. Steam and boiling water
will
come
out
of
the
soleplate.
Impurities and flakes (if any) will be
flushed out.
Release the self-clean button as
soon as all water in the tank has been
used up.
Repeat the self-clean process if the iron
still contains a lot of impurities.
ANTI-CALC SYSTEM
A special resin filter inside the water
reservoir softens the water and prevents
scale build-up in the plate. The resin
filter is permanent and does not need
replacing.
Please note:
Use tap water only. Distilled and
dematerialized water makes the “Zero-
Calc” anti-calc system ineffective by
altering
its
physicochemical
characteristics.
ANTI-DRIP SYSTEM
With the anti-drip system, you can
perfectly iron even the most delicate
fabrics.
Always iron these fabrics at low
temperatures. The plate may cool down
to the point where no more steam
comes out, but rather drops of boiling
water that can leave marks or stains. In
these cases, the Anti-drip system
automatically
activates
to
prevent
vaporization, so that you can iron the
most delicate fabrics without risk of
spoiling or staining them.
VERTICAL STEAM
Vertical steam allows you to use the
iron like a steamer, to steam out
wrinkles on hanging garments. Hold the
iron with the tip of the iron upright in a
vertical position and about 6 inches
away from the garment. Press and
release the “burst of steam” button (10)
on the iron to release steam onto the
wrinkle. Move the iron to the next
wrinkle and press the button again. Do
not press this button more than once
every 5 seconds. Continue to steam the
garment until the wrinkles are released.
CARE AND CLEANING
1. Turn the Temperature Control Dial
to OFF, then disconnect the iron from
the wall outlet and cool it down
completely.
2. Deposits and other residues on the
sole plate can be removed with a cloth
soaked in a vinegar/water solution.
3. The casing may the wiped with a
damp cloth and then polished with a dry
one.
4. Never use any abrasives to clean the
sole plate.
5. Keep the sole plate smooth, avoid
contact with metal objects.
6. When you have finished ironing or
you are leaving iron unattended:
-
turn the steam control knob to
position “0”.
-
stand the iron upright.
-
disconnect the iron from the wall
outlet
7. Do not allow children to touch the
iron or the power cord whom ironing.
8. Do not immerse die iron or the cord
into water or any other liquid.
9. Do not touch hot metal parts, hot
water or steam. These parts become hot
and may cause burns. Take care if you
turn die iron upside downs: there may
be not hot water in the tank. The plug
and cord should not be allowed to touch
the hot sole plate. Let the iron cool
down completely before taking it away.
Roll the power cord around the iron for
storage.
10. Disconnect die iron from the wall
outlet for filling in water or when you
remove the water after use.
11. The iron is for household use only.
12. Save the instruction manual for
future reference
Notes:
Some parts of the iron have been
slightly greased and as result the iron
may smoke slightly when switched on
for the first time. It will not happen
again after a few uses.
Before using for the first time,
remove any protective films or stickers
from the sole plate and the cabinet.
Then clean the sole place with a soft
cloth.
When using the iron for the first
time, test it on an old piece of fabric to
ensure that the sole plate and water
tank are completely clean.
CHOICE OF WATER
This iron can be used with normal
tap water.
If the water in your area is
particularly hard, it is advisable to use
distilled or demineralized water.
Do not use chemically descaled
water or any other liquids for refilling.
HOW TO FILL IN WATER
Set the Steam Control Knob “0” and
the temperature Control Dial to OFF.
Unplug the iron from the wall outlet.
Pour water into the water inlet.