Saturn ST-CM7089 Arabica - Инструкция (Страница 6)

10
and waiting for a moment, the appliance
begins to be heated until the green
lamp is illuminated, it shows the heating
is finish.
5. Remove the frothing device from the
steam wand.
6. Dip the steam wand into the liquid to
be heated. Turn the steam control knob
in anti-clockwise slowly to start making
steam.
7. When the required temperature is
reached, you can turn the steam control
knob to the minimum position.
8. Press and release the ON/OFF button
to the higher position which is the
“
O FF
” position to cut the power source
off.
CLEAN AND MAINTENANCE:
Cut off power source and let the coffee
maker cool down completely before
cleaning.
Clean housing of coffee maker with
moisture-proof sponge often and clean
water tank, drip tray and removable
shelf regularly then dry them.
Note: Do not clean with alcohol or
solvent cleanser. Never immerse the
housing in water for cleaning.
Detach the metal funnel through turn it
clockwise, get rid of coffee residue
inside, then you can clean it with
cleanser, but at last you must rinse with
clear water.
Clean all the attachments in the water
and dry thoroughly.
CLEANING MINERAL DEPOSITS
1. To make sure your coffee maker
operating efficiently, internal piping is
cleanly and the peak flavor of coffee,
you should clean away the mineral
deposits left every 2-3 months.
2. Fill the tank with water and descaler
to the MAX level (the ratio of water and
descaler is 4:1, the detail refers to the
instruction of descaler. Please use
“household descaler”, you can use the
citric acid (obtainable from chemist’s or
drug stores) instead of the descaler (the
one hundred parts of water and three
parts of citric acid).
3. According to the program of pre-
heating, put the metal funnel (no coffee
powder in it) and carafe (jug) in place.
Brewing water per “PRE-HEATING”.
4. Press down the ON/OFF button to the
” lower position which is the “
position, the power indicator (red) will
be illuminated, you should press the
pump control button to the lower
11
position which is the position, make
sure the coffee/steam button is on the
higher position which is the
position, when there is water flowing
out and close the pump by pressing the
pump control button again to the
“
S T O P
” position, and waiting for a
moment, the coffee maker begins to be
heated.
5. When the ready indicator (green) is
illuminated, it shows the heating is
finish. Pressing down the pump control
button to the lower position which is the
“ ” position and make two cups
coffee (about 2Oz). Then close the
pump and wait for 5s.
6. Press down the coffee/steam button
to the lower position which is the
position, waiting for until the green
indicator is illuminated. Make steam for
2min, then turn the steam control knob
to the minimum position to stop making
steam. Press and release the ON/OFF to
the higher position which is the “
O FF
”
position to stop the unit immediately,
make the descalers deposit in the unit
at least 15 minutes.
7. Restart the unit and repeat the steps
of 4-6 at least 3 times.
8. Then pressing and release the
coffee/steam button to the higher
position which is the position, when
the green lamp is illuminated, press
down the pump control button to the
lower position which is the “ ”
position to brew until no descaler is left.
9. Then brewing coffee (no coffee
powder) with tap water in the MAX
level, repeat the steps of 4-6 for 3 times
(it is not necessary to wait for 15
minutes in step of 6), then brewing until
no water is left in the tank.
10. Repeat the step of 9 at least 3 times
to make sure the piping is cleanly.
TROUBLE SHOOTING
Symptom
Cause Corrections
There is
much water
in the drip
tray.
Please clean
the drip
tray.
Water
leaks
from the
bottom of
coffee
maker.
The coffee
maker is
malfunction.
Please
contact with
the
authorized
service
facility for
repairing.
Water
leaks out
of outer
side of
filter.
There is
some coffee
powder on
filter edge.
Get rid of
them.