Care and cleaning, Note, Replacing method of the lamp bulb – Инструкция по эксплуатации Sharp SJP-641 NSL
Страница 8: Switching off your refrigerator, What to do before you call for service, Sharp corporation, Evaporating pan & cover; how to remove, How to set, It is normal, If you still require service
Внимание! Текст в этом документе был распознан автоматически. Для просмотра оригинальной страницы Вы можете воспользоваться режимом "Оригинал".
CARE AND CLEANING
Some
household
cleaning
chemicals
may
affect
the
inside
surfaces
and
plastic
shelves
resulting
in splitting or cracks occurring.
When
cleaning
all
plastic
parts
in
side
this
refrigerator,
only
use
di
luted
dishwashing
liquid(soapy
water).
Make
sure
that
all
plastic
parts
are
thoroughly
rinsed
with
water after cleaning.
1.
Remove
the
shelves
and
pockets
from
the
cabinet
and
door.
Wash
them
in
warm
soapy
dishwashing
water; rinse in clean water and dry.
2.
Clean
the
inside
with
a
cloth
soaked
in
warm
soapy
dishwashing
water.
Then,
use
cold
water
to
wipe
off
soapy water.
S.Wipe
the
exterior
with
a
soft
cloth
each
time
it
is
soiled.
4.
Clean
Magnetic
door
seal
with
a
toothbrush
and
warm soapy dishwashing water.
5.
Evaporating
pan
should
be
removed
and
cleaned
once a year.
NOTE:
• Do not use polishing powder, benzine, hot water etc.
•
If
undiluted
detergent
is
used
or
soapy
water
is
not
wiped
off
thoroughly,
cracking
of
plastic
parts
can
re
sult.
•
Wipe
any
food
oils
adhered
to
plastic
components
as they can cause cracking of the plastic surface.
•
The
glass
shelves
weighs
approximately
3kg
each.
Hold
firmly
when
removing
from
the
cabinet
or
carry
ing.
Evaporating pan & cover;
How to remove
1
.Hold
both
sides
of
Evapo
rating
pan
cover
and
an
gling upward.
2. Pull Evaporating pan out.
How to set
1.
Put
Evaporating
pan
on
Radiator
plate,
then
slide
it in completely.
2.
Fit
the
pawls
of
Evaporat
ing
pan
cover
into
the
holes
of
the
cabinet,
then
push the cover to attach.
Evaporating pan
Evaporating pan
cover
Hole
Pawl
Replacing method of the lamp bulb
1. Unplug the refrigerator first to prevent electric shock.
2. Remove the light cover.
3. Replace the lamp bulb with the same type.
Freezer: base E12, MAX 10W, T-20
Refrigerator: base El2, MAX 15W, T-20
Switching off your refrigerator
If
you
switch
your
refrigerator
off
when
you
are
going
away
for
an
extended
period,
remove
ail
food,
clean
the
interior
thoroughly.
Remove
the
power
cord
plug
from
the
power
socket
and
leave
all doors open.
WHAT TO DO BEFORE YOU CALL FOR SERVICE
Before
you
call
for
service,
check
the
following
point.
IT IS NORMAL
for
the
refrigerator
to
produce
the
following sounds.
• Loud noise produced by the compressor when op
eration starts — Sound becomes quieter after a while.
• Loud noise produced once a day by the compressor
—
Operating
sound
produced
immediately
after
au
tomatic defrost operation.
• Sound of flowing fluid (gurgling sound, fizzing sound)
—
Sound
of
refrigerant
flowing
in
pipes
(sound
may
become louder from time to time).
•
Cracking
or
crunching
sound
—
Sound
produced
by
expan
sion
and
contraction
of
inner
walls
and
internal
parts
during
cooling.
*
Squeaking
sound
—
Sound
produced
by
expansion
and
con
traction of internal parts.
IT IS NORMAL
that the outside of a cabinet may be hot when
touched.
The
hot
pipe
is
in
the
cabinet
in
order
to
prevent
dew
generation.
IF YOU STILL REQUIRE SERVICE
Refer to your nearest service agent approved by SHARP
12
SHARP CORPORATION
Напечатано
в
Таиланде
/
Printed
in
Thailand
TINS-A755CBRZ 06LK (T^ (1)