Directions for use, Назначение проводов и разъемов центрального блока – Инструкция по эксплуатации Mongoose IQ-200/1
Страница 15
Автомобильный охранный комплекс “MONGOOSE”. Модель IQ-200/1
15
РУССКИЙ
Назначение проводов и
разъемов центрального блока
N
Назначение провода
Цвет провода
Примечание
1
Выход на сирену
Коричневый
“+” 2 А
2
Выход на пейджер
Белый
“+” 300 мА
3
Выход состояния
Коричневый/белый
“-”300 мА
4
Концевик багажника
Серый
“-”
5
Выход отпирания багажника
Голубой/черный
“-”300 мА (1 сек.)
6
Вход Зажигание
Оранжевый
+12 В
7
Концевик двери “-”
Зеленый
8
Корпус
Черный
“-”
9
Выход управления
Зеленый/красный
“-” 300 мА
стеклоподъемниками
(20c импульс
(“Comfort”)
при постановке
на охрану)
10
Питание блока
Зеленый/коричневый
+12В, Пр. 5А
11
Выход на фонари 1
Черный/белый
12
Питание фонарей
Красный
+12В, Пр. 15А
13
Выход на фонари 2
Черный/зеленый
14
Концевик двери “+”
Желтый
15
Реле отпирания НЗ контакт
Голубой/желтый
16
Реле отпирания ОБЩ контакт
Голубой/красный
Внутреннее реле
17
Реле отпирания НО контакт
Красный/черный
18
Реле запирания НЗ контакт
Серый/желтый
19
Реле запирания ОБЩ контакт
Серый/красный
Внутреннее реле
20
Реле запирания НО контакт
Красный/желтый
Вход для светодиода
2-контактный разъем
Вход кнопки аварийного
2-контактный разъем
отключения
Два входа для 2-зоновых
Два 4-контактных
датчиков
разъема
Силовой выход блокировки
Черные
Внутреннее реле 30 А
(2 провода)
Выход программируемого
Коричневый/черный
“-”300 мА
канала
User’s Guide & Installation Manual. Revision 1
3 0
Emergency disarm button.
The emergency disarm button can be operated in either the normal or coded
mode, which is set by programming.
Emergency disarm.
In the case of alarm transmitter missing or broken, the system provides the
following emergency disarm options:
Normal emergency disarm mode.
If no PIN code has been preset for the system, an emergency disarm will call
for pressing the button once with the ignition on, then turning off the ignition.
Coded emergency disarm mode.
If a PIN code is set, an emergency disarm will require pressing the button as
many times as the value of this code with the ignition on, then turning off
the ignition.
Directions for use
Basic arm status features.
Arm.
In order to arm the alarm, press button 1 of the transmitter; the siren will
«chirp» once and the lights will flash once. The system LED will blink slowly;
the door locks will be locked (if connected).
Armed status.
In the arm mode the alarm system controls the status of all connected
terminal switches, the control ignition input, and twq optional 2 stage sensors
(shock sensor, space disturbance sensor, etc.). In addition, the car engine is
blocked in this mode. If any guard zone is violated, an alarm mode is triggered
which lasts for 30 seconds (program selected).
Armed
slow flashes
Disarmed
off
Arming
quick flashes
Valet mode
continually lit
LED indication of status