Det-Tronics UD10 FlexVu Explosion-Proof Universal Display Unit - Инструкция (Страница 95)

Main Menu
Process Vars
Display Status
Device Status
Display Setup
Device Setup
Device Cal
Display Test
Process Vars
Gas Name xxxxx
Gas Value x.xx
High Alarm Y/N
Low Alarm Y/N
Aux Alarm Y/N
Analog Input x.xx mA
Analog Output x.xx mA
URV x.xx
LRV x.xx
Fault Y/N
Display Test
Self Test
Response Test
Loop Test
D/A Trim
History
Display History
Event Log
Display Info
RTC
Serial Number xxxxx
I/O Board ID xxx
Mfg Date
dd/mm/yyyy
F/W Rev xxxxx
Universal Rev xxxxx
Field Dev Rev xxxxx
Running Hours xxxxx
Temperature xx.xx C
Heater Ctrl Automatic/On/Off
Backlight Ctrl Automatic/On/Off
Input Voltage xx.xx
RS485
Baud Rate xxxxx
Parity xxxxx
Poll Address xxxxx
Fault
EE FAULT ON/OFF
ADC FAULT ON/OFF
24V FAULT ON/OFF
FLASH FAULT ON/OFF
RAM FAULT ON/OFF
WDT FAULT ON/OFF
12V FAULT ON/OFF
5V FAULT ON/OFF
3V FAULT ON/OFF
O/P LOOP FAULT ON/OFF
INPUT LOOP FAULT ON/OFF
Event Log
Event xxxxx
Date
dd/mmm/yyyy
Time hh:mm:ss
RTC
Displayed Y/N
Seconds xx
Minutes xx
Hours xx
Day xx
Month
xx
Year xx
HART Option
Tag xxxxx
Descriptor xxxxx
Date dd/mmm/yyyy
Message xxxxx
Final assy num xxxxx
RTC
Displayed Y/N
Seconds xx
Minutes xx
Hours xx
Day xx
Month
xx
Year xx
Mode Select
HART Device
PIR9400
C706X
505
NTMOS
CGS
Generic Device
RS485
Baud Rate
Parity
Poll Address xxxx
Baud Rate
1200
2400
4800
9600
19.2K
Parity
None
Even
Odd
D/A Trim
Zero Trim
Gain Trim
Loop Test
Set 4-20 mA ->
Device Info
Manufacturer
Model
CGS
Gas Name xxxxx
Unit of Measure %LFL
URV 100
LRV 0
K-Factor xxxx
Response xxxx
Device Status
Device Info
Fault/status
Calibration Log
Calibration Log
Cal ID xxxx
Date dd/mmm/yyyy
Time hh:mm:ss
Zero 0 mV
Span xx.xx mV
Device Setup
Device Option
Device Option
Gas Name xxxxx
K-Factor xxxxx
Device Cal
Calibration
Cal Gas
xxxxxxxx
Cal Gas Concentration 50.00
K Factor
xx.xx
Calibration
Execute
Status
ANY FAULT ON/OFF
CAL ACTIVE ON/OFF
WARM UP ON/OFF
LOW RELAY ACTIVE ON/OFF
HI RELAY ACTIVE ON/OFF
AUX RELAY ACTIVE ON/OFF
CURRENT FIXED ON/OFF
MB WRITE PROTECT ON/OFF
HART SELF TEST ON/OFF
LON ATTACHED
ON/OFF
RESPONSE TEST ON/OFF
MANUAL SELF TEST ON/OFF
INPUT HART ON/OFF
Display Status
Gen Info
Fault/Status
History
Display Info
RS485
Debug Menu
Gen Info
Manufacturer
Model
UD-10
Tag xxxxx
Descriptor xxxxx
Date dd/mm/yyyy
Message xxxxx
Final Assy Num xxxxx
Device ID xxxxx
Fault/Status
Op Mode xxxxx
Fault Y/N
Status Y/N
Display History
Running Hours xxxx
Max Temp xx.xx C
Max Temp Time xx:xx:xx
Min Temp xx.xx C
Min Temp Time xx:xx:xx
Max Reset Temp xx.xx C
Max Reset Time xx:xx:xx
Min Reset Temp xx.xx C
Min Reset Time xx:xx:xx
Set 4-20 mA
3.5mA
4 mA
6 mA
8 mA
10 mA
12 mA
14 mA
16 mA
18 mA
20 mA
6901 West 110th Street
Minneapolis, MN 55438
USA
6901 West 110th Street
Minneapolis, MN 55438
USA
Faults
Loop fault ON/OFF
Warm up
ON/OFF
Sensor Fault ON/OFF
Cal Fault ON/OFF
Zero Drift Fault ON/OFF
CGS Comm Fault ON/OFF
Faults/Status
Faults Y/N
Status Y/N
Display Setup
Alarm Setting
Mode Select
HART Option
RTC
RS485
Input Loop Cal
Contrast Control
Output Mode
Backlight Ctrl
Write Protect
Output Mode
Standard
Replicate
Status
Weak Sensor ON/OFF
Alarm Setting
Rst Latch Alarms
Hgh Alarm Level
xx.xx
Hgh Alarm Latch Y/N
Hgh Alarm NE/ND
Low Alarm Level
xx.xx
Low Alarm Latch Y/N
Low Alarm NE/ND
Aux Alarm Level
xx.xx
Aux Alarm Latch Y/N
Aux Alarm NE/ND
Write Protect
Change State
Change Password
Write Protect xxxx
Backlight Ctrl
Off
On
Automatic
1-Oct-10 CGS 2.80
Detector Electronics
Hgh Alarm NE/NDE
NE-NORMALY ENERGIZED
NDE-NORMALY DEENERGIZED
Low Alarm NE/NDE
NE-NORMALY ENERGIZED
NDE-NORMALY DEENERGIZED
Aux Alarm NE/NDE
NE-NORMALY ENERGIZED
NDE-NORMALY DEENERGIZED
Debug Menu
HART Errors xxxxx
Modbus Errors xxxxx
Output Readback
xx.xx mA
Analog Input xx.xx mA