ViTESSE VS-232 - Инструкция (Страница 3)

P/3 P/4
• Before operating your Multi Food Processor, remove the seeds of those fruits
such as peaches, apricots, plums, etc., and peel those dried fruits/nuts such
as almonds, hazelnuts, walnuts , etc. Meat to be processed must be boneless,
free from fats or sinews.
BEATING / KNEADING
•
Fix the accessory holder on the centering spindle located in the glass bowl.
• Place the beating and kneading disc onto the accessory holder.
• Then add any foods you wish to beat or knead.
• After placing the bowl lid on the glass bowl make sure that when fixing the
main body the starting button is in the position of down and that the locking
latches are properly secured on the handles located in the glass bowl.
• To operate the unit first turn the starting button located in the main body to the
position of close up, then ensure operating for beating or kneading process at
any speed by using speed steps after making sure that the locking, latches are
firmly secured.
• Thanks to a specially designed beating and kneading disc, you can beat even
1 egg by using your Multi Food Processor.
SUGGESTIONS FOR USE
•
Before operating your Multi Food Processor wash any accessories of it using
warm water.
• After placing the non-slip rubber pad onto a flat surface, fix your appliance on
such rubber pad.
• Make sure that there is no food or material between the bowl and accessory,
when attaching such accessory for any process you wish to make.
• When operating your appliance, with your other hand grasp from the handle of
the glass bowl to ensure more practical use.
• Glass bowl of your appliance is intended for use in microwave oven only.
Never use it in electric or gas oven.
WARNING
1- When using your appliance, before coming closer to moving parts or before
removing accessories turn on/off switch to down position.
2- Never open locking latches by pulling them. They will be automatically opened
when you turn the starting button to down position.
3- Your appliance is designed to operate for up to 10 sec. Ensure not to exceed
this duration when preparing foods. Otherwise your unit may be damaged.
Allow your appliance to cool down for about 1 minute per every operation of 10
seconds.
CUTTING
•
Fix the accessory holder on the centering spindle located in the glass bowl.
• Remove the metal blade for cutting from its case, and insert it on the
accessory holder.
• Put any foods you wish to cut into the bowl. Do not put any foods into the glass
bowl unless attaching a blade for cutting in its place.
• After placing the bowl lid on the glass bowl make sure that when fixing the
main body the starting button is in the position of down and that the locking
latches are properly secured on the handles located in the glass bowl.
• To operate the unit first turn the starting button located in the main body to the
position of close up, then ensure operating at any speed by using speed steps
after making sure that the locking latches are firmly secured.
• “PULSE” button located in the side panel allows you to exercise a pulse
operation and maximum power. By using this pulse function you can not only
obtain good results in a respectively simple way especially in cutting
processes, but also extend the life cycle of your appliance.
• After operating your unit if there remains some uncut parts or sticking
ingredients to edges of the bowl mix the materials using a spatula, and re-
operate the appliance depressing the “PULSE” function 2 or 3 times.
MATERIALS
MEAT
ONION/GARLIC (divided)
FRUIT (divided)
PARSLEY
HAZELNUT/AL MOND/MALNUT
CHEESE
BISCUIT
CAPACITY MAX.
500 gr.
600 gr.
800 gr.
100 gr.
350 gr.
300 gr.
350 gr.
RECOMMEMDED SPEED
MAX/PULSE
MAX/PULSE
MAX/PULSE
MAX/PULSE
MAX/PULSE
MAX/PULSE
MAX/PULSE
SUGGESTIONS FOR CUTTING
MATERIALS
EGG
MAYONNAISE
CREAM
PASTRY DOUGH
CAPACITY MAX
6PCS
500 gr.
250 gr.
800 gr.
RECOMMENDED SPEED
MAX / PULSE
10/MAX
10/MAX
MAX / PULSE
SUGGESTIONS FOR BEATING AND KNEADING
GRATING AND SLICING
•
Fix the accessory holder on the centering spindle located in the glass bowl.
• For slicing or grating process, keep the holder disc in such position with the
disc side facing upwards, and first place the protruding part of the selected
grating or slicing blade and then push on the other side slightly. (To remove
grating or slicing blade from the disc, slightly push from downward.) If your
blade is in alignment with the surface of the holder disc and does not move
when pressed from upwards, it means that such blade is secured in its place.