WORX Tools WU366.9 - Инструкция (Страница 13)

Cordless Hammer Drill ENG
13 12
Important charging notes:
1.For a new battery or a battery that has been
in storage for sometime, please recharge the
battery before use. If you want to store the
battery for a long time, please fully charge the
battery pack to ensure maximum battery life.
2.Longer life and better performance can be
obtained if the battery pack is charged when
the air temperature is between 65
0 F and 75 0 F
(18 0 -24 0 C). Do not charge the battery pack in air
temperatures below + 40 0 F (+4.5 0 C), or above
1050 F (40.5 0 C). This is important as it can
prevent serious damage to the battery pack.
3.Never freeze your charger or immerse charger
in water or any other liquid.
4.When the battery pack fails to produce
sufficient power on jobs that were previously
done easily, please recharge you battery, do
not continue to use under this condition. You
may charge a partially used pack whenever you
desire with no adverse affect on the battery
pack.
5. When charging it is normal that the charger
and battery pack may become warm to touch.
6.If the battery pack does not charge properly:
a.Check current at power outlet by plugging in
another appliance.
b.Plug and unplug to check whether the charger
is ok.
c.Check whether the battery has been
damaged
d.Move the charger and battery pack to a
location where the surrounding air temperature
is approximately 65
0 F - 75 0 F (18 0 -24 0 C).
e.If the charging problem persists, take the
tool, battery pack and charger to an authorized
service center.
f.Under certain conditions, when the charger
is plugged into the power supply, the exposed
charging contacts inside the charger can be
shorted by foreign material. Foreign materials
of a conductive nature such as metallic particles
should be kept away from charger cavities.
Always unplug the charger from the power
supply when there is no battery pack in the
charger or before attempting to clean.
4. TO REMOVE OR INSTALL BATTERY
PACK
Locate latches on side of battery pack and
depress both sides to release battery pack from
your drill. Remove battery pack from your drill
(See Fig B). After recharge insert the battery
pack into drill’s battery port. A simple push and
slight pressure will be sufficient.
5. ON/OFF SWITCH WITH BRAKE
FUNCTION
Depress to start and release to stop your
drill (See Fig C). The on/off switch is fitted
with a brake function which stops your chuck
immediately when you quickly release the
switch.
6. SWITCH LOCK
The switch trigger can be locked in the OFF
position. This helps to reduce the possibility of
accidental starting when not in use. To lock the
switch trigger, place the direction of rotation
selector (2) in the center position (See Fig C).
7. REVERSIBLE
The direction selector (2) located above the
switch trigger controls the direction of rotation.
With the drill held in normal operating position,
the direction of rotation selector should be
positioned to the right of the switch for drilling.
The rotation direction is reversed when the
selector is positioned to the left. When the
selector is in the center position, the switch
trigger is locked (See Fig C).
Warming: Never change the direction
of rotation when the chuck is rotating,
wait until it has stopped !
8. VARIABLE SPEED
This tool has a variable speed switch that
delivers higher speed and torque with
increased trigger pressure. Speed is controlled
by the amount of switch trigger depression.
Warming: Do not operate for long
periods at low speed because excess
heat will be produced internally.
9. TWO-SPEED GEAR TRAIN
The drill has a two-speed gear train designed
for drilling or driving at LO (mark is 1) or HI
(mark is 2) speeds. A slide switch is located on
top of the drill to select either LO or HI speed
RUS-WU364 WU366-M-060818.indd 13 2006-8-18 17:52:41