Panasonic EW1211W835 - Инструкция (Страница 4)

c c
remaining waterafteruse. operating
the unitwithoutwatermayresultina
malfunction.
1. Attach the nozzle and the tank
firmly onto the unit (Fig.5).
2. Open the cap of the water tank,
hold the unit so it is level, and fill
the tank with cold or warm water,
not hotter than 40“C (Rg.6).
• Do not put salt, toothpaste,
powder, or other chemicals Into
the water tank.
• Certain liquid mouthwash may
damage the device by causing
the housing or the tank to crack.
When using mouthwash, rinse
the tank arid main unit with wa­
ter immediately after use. Be
especially careful when wash­
ing the hose connections at the
main unit and the tank.
CAUTION:
Never fill the tank with hot water!
The gumlines can be very sensitive
and can be easily damaged by hot
water.
3. Close the cap, making sure it
locks in place (Fig.7).
4. Press the mode switch and select
the desired water jet inode. The
mode indicator will display the
previously selected mode, if the
unit is not used for more than 30
days, or after the unit has been
fully charged from its fully dis­
charged state, the mode is initial­
ized to its soft air-in jet water set­
ting.
If you want to use a different mode,
press the mode switch until it
changes to the desired setting.
Pressing the mode switch will
change the mode from soft air-in
to normal air-in to jet.
Mode and its indicator (Fig.8)
© Mode switch
Pressing the mode switch will
change the water jet setting and
the respective mode indicator will
light up.
@ "Jet" mode
This mode is for removing food
particles trapped between the
teeth.
(D "Normal air in" mode
This mode is for removing food
particles and for massaging the
gums and rinsing between the
teeth and gums.
® "Soft air in" mode
This mode is for gently massag­
ing the gums.
Note:
When you use the unit for the first
time, press the operation switch to
turn the unit on and test each of the
water jet modes with the tank filled
with water.
5. Insert the nozzle into your mouth.
• Bend over the sink and hold the
unit in an upright position with
the nozzle pointing toward your
teeth.
6. Press the operation switch.
• Close your mouth slightly to
contain the water spray.
• The unit starts operating in the
mode selected in step 4 above.
• Pressing the mode switch dur­
ing use will change the mode.
• A fully filled water tank provides
approximately 35 seconds of
use.
• The ventilation hole in the rear
of the unit allows for easier wa­
ter suction of the hose. (If the
unit is tilted too much, water
may come out from the ventila­
tion hole; this is normal.)
CAUTION:
• Do not turn the switch on before
putting the nozzle in your mouth.
• Do not hold the tip of the nozzle
firmly against the teeth or gums.
7. Turn the nozzle wheel with your
thumb to reach all areas in your
mouth (Fig .9).
• Keep your mouth slightly
opened so that the water can
flow out.
• Systematically rinse all teeth
and the spaces between them.
• Make sure that you always hold
the device in an upright position
with the nozzle pointing up­
wards. If you turn the device up­
side down, no water from the
tank will be taken in.
• Remember that rinsing the mouth
is not a substitute for tooth-
brushing. Brush your teeth or
dental prosthesis immediately
after a meal for at least five min­
utes and then use the device.
8. After use, press the operation
switch to turn off the unit.
• Be sure to turn off the unit while
the nozzle is still inside your
mouth.
CAUTION:
• This device is designed exclusively
for use in the oral cavity.
Never use it for rinsing or cleaning
other parts of the body (e.g., ears
or eyes).
• During the first several uses, light
bleeding of the gums may occur.
If your gums are healthy, any
bleeding during use should stop in
one to two weeks. If bleeding per­
sists after two or more weeks of
use, consult your dentist.
AFTER USE (Fig.lO)
t.With the nozzle still attached,
open the cap of the water tank
and pour out the water.
2. Switch on the device for a few
seconds to pump out any re­
maining water.
• Always pour out the remaining
water and empty out the nozzle.
This helps to prevent contamin­
ation and bacterial growth in
the remaining water.
3. Turn off the device and return it
to the charger.
• The charging indicator will light-
up.
4. While pressing the nozzle re­
lease button, remove the nozzle
from the unit and place it on the
nozzle stand.