Parts identification, Before use, To make kubbe – Инструкция по эксплуатации Panasonic MK-G20PR

Страница 3: Jamming, Cautions, To mince meat, To clean

Внимание! Текст в этом документе был распознан автоматически. Для просмотра оригинальной страницы Вы можете воспользоваться режимом "Оригинал".

Advertising
background image

Parts identification

Before use

To make kubbe

Jamming

© Switch(es)

© Locking knob

© Motor housing

© Opening

© Food pusher

© Hopper plate

© Head

© Feed screw

© Cutting blade

©~© Attachments

© Cutting plate (fine)

© Cutting plate (medium)

© Cutting plate (coarse)

(m) Kubbe attachment A

@ Kubbe attachment B

@ Cap

Cautions

Unplug when assembling or disassembling the unit.

Close supervision is necessary when any appli­
ance is used near children.

When carrying the unit, be sure to hold Motor Housing
with both hands, not to hold only Hopper Plate.

Do not fix Cutting Blade and Cutting Plate when
using Kubbe Attachments.

Never feed food with hand. Use Food Pusher.

Do not grind hard foods such as bones and nuts.

Do not grind ginger and other materials with hard fiber.

To avoid jamming, do not force to operate the

unit with excessive pressure.

If the unit jams due to hard materials lodged on

to Feed Screw or Cutting Blade, switch off imme­
diately and clean the unit.

(See "Jamming" on page 4.")

When the circuit breaker activates, do not switch on.

Never try to undo the parts or to repair the unit
by yourself.

This product is intended for household use only.

Make sure that the voltage and frequency indi­
cated on the bottom plate are the same as your

local supply.

Wash all the parts (except those that do not
touch foods ©,©,(^and ©) in warm soapy

water.

Before plugging in, ensure Switch is off.

To mince meat

(Assembling)

I 1 I Place Head tightly onto Opening of Motor

Housing. Holding Head with one hand, place
Locking Knob into the hole on the side of Motor
Housing and tighten it clockwise.

Place Feed Screw into Head, long end first, by
turning Feed Screw slightly until it is set into Motor
Housing.

Place Cutting Blade onto Feed Screw shaft with

the blade facing the front as illustrated.

• If it is not fitted properly, meat will not be

ground.

4

Place desired Cutting Plate next to Cutting Blade,

fitting protrusions in the slots.

Screw Cap into place until tight.
• Do not over tighten.

Place Hopper Plate on Head and fix into position.

Locate the unit on a firm place.
• The air passage at the bottom and the side of

Motor Housing should be kept free and not
blocked.

(Mincing meat)

Cut all foods into pieces so that they fit easily into
Hopper opening.

Plug in, then switch on.

0 Feed foods into Hopper Plate.

— • Use Food Pusher.

—Recipe—
(Stuffing)

100 g
1 1/2 tablespoons

1 1 / 2 tablespoons
1/3 teaspoon
1/2 teaspoon
1 1 / 2 tablespoons

mutton

olive oil
onion (cut finely)
all spice
salt
flour

Mince mutton once or twice.

Fry onion until brown and add minced mutton, all
spice, salt and flour.

(Outer cover)

450 g

150 - 200 g
1 teaspoon

1

a pinch

dash

lean meat
flour
all spice
nutmeg
powdered red pepper

pepper

Mince meat three times and mix all ingredients
together in a bowl.
• More meat and less flour for outer cover creates

better consistency and taste.

Grind the mixture three times.

Disassemble by reversing the steps from [^] - [3j to
remove Cutting Plate and Cutting Blade.

I 7 I

Place Kubbe Attachments A and B onto Feed

Screw shaft together, fitting protrusions in the slots.

8

Screw Cap into place until tight.
• Do not over tighten.

9

Following the same steps as in 15j - ( 6 j , make the
cylindrical outer cover.

Form kubbe as illustrated below and deep fry.

m r—di

d::>

# %

When the circuit breaker automatically stops the

motor, or when the motor continues to function
but no meat comes out of Cutting Plate, due to

jamming of bone or other materials, switch off.

• Do not switch on.

Clean the unit. (See "To clean" below.)

To clean

(Disassembling)

Make sure that the motor has stopped completely.
Disconnect the plug from the power outlet.

Disassemble by reversing the steps from S - [U .

10

Cap has pins for easy unscrewing.

To remove Cutting Plate easily,

[Tl] place a screwdriver between Cutting Plate and

— Head as illustrated and lift up.

(Cleaning)

Remove meat, etc.

Wash each part in warm soapy water.

• A bleaching solution containing chlorine will dis­

color aluminum surfaces.

• Do not immerse Motor Housing in water, but only

wipe it with a damp cloth.

• Thinners and benzines will crack or change the

color of the unit.

A little salad oil on ® ~ © after washing and drying
will keep them lubricated.

Caution:
Do not wash washable parts in a dishwasher.

After use, switch off and unplug.

-3-

-4-

Advertising
Эта инструкция подходит к следующим моделям: