Инструкция по эксплуатации Pioneer AVH-P4100DVD

Avh-p4100dvd, Installation manual руководство по установке, Connecting the units

Advertising
background image

Installation Manual

Руководство по установке

DVD RDS AV RECEIVER

DVD RDS AV РЕСИВЕР

AVH-P4100DVD

WARNING

• To avoid the risk of accident and the potential

violation of applicable laws, the front DVD or TV

(sold separately) feature should never be used

while the vehicle is being driven. Also, rear displays

should not be in a location where it is a visible

distraction to the driver.

• In some countries or states the viewing of images

on a display inside a vehicle even by persons

other than the driver may be illegal. Where such

regulations apply, they must be obeyed and this

unit’s DVD features should not be used.

CAUTION

• PIONEER does not recommend that you install

or service your display yourself. Installing or

servicing the product may expose you to risk

of electric shock or other hazards. Refer all

installation and servicing of your display to

authorized Pioneer service personnel.

• Secure all wiring with cable clamps or

electrical tape. Do not allow any bare wiring to

remain exposed.

• Do not drill a hole into the engine compartment

to connect the yellow lead of the unit to

the vehicle battery. Engine vibration may

eventually cause the insulation to fail at

the point where the wire passes from the

passenger compartment into the engine

compartment. Take extra care in securing the

wire at this point.

• It is extremely dangerous to allow the display

lead to become wound around the steering

column or gearshift. Be sure to install the

display in such a way that it will not obstruct

driving.

• Make sure that wires will not interfere with

moving parts of the vehicle, such as the

gearshift, parking brake or seat sliding

mechanism.

• Do not shorten any leads. If you do, the

protection circuit may fail to work properly.

WARNING

LIGHT GREEN LEAD AT POWER CONNECTOR

IS DESIGNED TO DETECT PARKED STATUS

AND MUST BE CONNECTED TO THE POWER

SUPPLY SIDE OF THE PARKING BRAKE SWITCH.

IMPROPER CONNECTION OR USE OF THIS LEAD

MAY VIOLATE APPLICABLE LAW AND MAY RESULT

IN SERIOUS INJURY OR DAMAGE.

Note

• This unit cannot be installed in a vehicle without

ACC (accessory) position on the ignition switch.

ACC

ON

S

T

A

R

T

O

FF

ON

S

T

A

R

T

O

FF

ACC position

No ACC position

• Use this unit in other than the following conditions

could result in fire or malfunction.

— Vehicles with a 12-volt battery and negative

grounding.

— Speakers with 50 W (output value) and 4 ohm to

8 ohm (impedance value).

• To prevent short-circuit, overheating or malfunction,

be sure to follow the directions below.

— Disconnect the negative terminal of the battery

before installation.

— Secure the wiring with cable clamps or adhesive

tape. To protect the wiring, wrap adhesive tape

around them where they lie against metal parts.

— Place all cables away from moving parts, such

as gear shift and seat rails.

— Place all cables away from hot places, such as

near the heater outlet.

— Do not pass the yellow cable through a hole into

the engine compartment to connect to a battery.

— Cover any disconnected cable connectors with

insulating tape.

— Do not shorten any cables.

— Never cut the insulation of the power cable of

this unit in order to share the power to other

equipment. Current capacity of the cable is

limited.

— Use a fuse of the rating prescribed.

— Never wire the speaker negative cable directly to

ground.

— Never band together multiple speaker’s negative

cables.

• Control signal is output through blue/white cable

when this unit is powered on. Connect it to an

external power amp’s system remote control or the

vehicle’s auto-antenna relay control terminal (max.

300 mA, 12 V DC). If the vehicle is equipped with a

glass antenna, connect it to the antenna booster

power supply terminal.

• Never connect blue/white cable to external power

amp’s power terminal. Also, never connect it to the

power terminal of the auto antenna. Otherwise,

battery drain or malfunction may result.

• IP-BUS connectors are color-coded. Be sure to

connect connectors of the same color.

• Black cable is ground. This cable and other

product’s ground cable (especially, high-current

products such as power amp) must be wired

separately. Otherwise, fire or malfunction may

result if they are accidentally detached.

Parts supplied

Parts marked (*) are pre-installed.

This product

Power cord

USB cable

Holder*

Side bracket (2 pcs.)*

Trim ring

Frame

Flush surface screw

(5 mm × 8 mm) (8 pcs.)

(4 pcs. are pre-installed.)

Binding screw

(5 mm × 8 mm) (8 pcs.)

Binding screw*

(3 mm × 6 mm) (8 pcs.)

Rubber bush

Double-ended screw

Touch panel pen

<KSNZX> <08H00000>

Printed in Thailand

Отпечатано в Таиланде

<CRD4378-C/N> UW

Connecting the units

Connecting the units

Connecting the units

Advertising